Mini Clamp Multimeter

• Clamp allows measurement of AC and DC current in wires without disturbing the circuits or contacting live terminals
  
• Auto range simplifies operation: 0.01-400 Amps, 0.001-600 Volts
  
• Auto power-off selection - power turns off automatically after 10 minutes of non-use
  
• True RMS - required for accurate measurement of inverter output
  
• Large digital display makes reading measurements easy
  
• Data hold - press "HOLD" button during measurement to lock reading value
• Test leads included with meter
  

Features:

1811

Features:

• Accurate - used with the Vessel Systems Monitor VSM 422 PN 1800-can be precisely calibrated for each tank*
  
• Reliable - SSI Technologies, Inc. Fluid-Trac® is non-contacting eliminating any mechanical moving parts that can wear and cause intermittent or complete signal loss
  
• Digital filtering - Eliminates errors due to liquids sloshing in mobile tanks

1810

Features:

• Accurate - used with the Vessel Systems Monitor VSM 422 PN 1800 - can be precisely calibrated for each tank*
  
• Reliable - SSI Technologies, Inc. Fluid-Trac® is non-contacting eliminating any mechanical moving parts that can wear and cause intermittent or complete signal loss
  
• Digital filtering - Eliminates errors due to liquids sloshing in mobile tanks

1011

Features:

• Features watertight cap, easy installation, and twist locks securely with plug
  
• Designed to withstand the rigors of wet environments and constant vibration
  
• Large contact surfaces for good electrical connection
  
• Twist lock system-plug locks securely into socket
  
• Internal strain relief and cord seal
  
• Nickel plated copper alloy used for all current carrying components
  
• Front panel, rear panel, or surface mount

1010

Features:

• Moisture proof sealing ring around the shaft to keep out spray and make it seat firmly in the outlet
  
• "ON" indicating LED
  
• Strain relief
  
• Built-in 10 Amp fuse
  
• Designed to withstand the rigors of wet environments and constant vibration
  
• Large contact surfaces for good electrical connection
  
• Twist lock system-plug locks securely into socket
  
• Internal strain relief and cord seal
  
• Nickel plated copper alloy used for all current carrying components
  
• Front panel, rear panel, or surface mount

9004e
e-Series Battery Switch Single Circuit ON/OFF w/ Alternator Field Disconnect


Includes AFD (Alternator Field Disconnect)

• CE Marked
• Ignition protected - Safe for installation aboard gasoline powered boats
• Case design allows surface or rear panel mounting
• Meets American Boat and Yacht Council (ABYC) requirements for battery switches
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
• 7/8" (22.22mm) stud length to accept multiple cable terminals
• Tactile textures indicate knob position by feel only

9001e
e-Series Battery Switch Selector

• Make-before-break contact design allows switching between battery banks without power interruption
• CE Marked
• Ignition protected - Safe for installation aboard gasoline powered boats
• Case design allows surface or rear panel mounting
• Meets American Boat and Yacht Council (ABYC) requirements for battery switches
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
• 7/8" (22.22mm) stud length to accept multiple cable terminals
• Tactile textures indicate knob position by feel only

9003e
e-Series Battery Switch Single Circuit ON/OFF

• CE Marked
• Ignition protected - Safe for installation aboard gasoline powered boats
• Case design allows surface or rear panel mounting
• Meets American Boat and Yacht Council (ABYC) requirements for battery switches
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
• 7/8" (22.22mm) stud length to accept multiple cable terminals
• Tactile textures indicate knob position by feel only

9002e
e-Series Battery Switch Selector w/ Alternator Field Disconnect

• Make-before-break contact design allows switching between battery banks without power interruption

• CE Marked
• Ignition protected - Safe for installation aboard gasoline powered boats
• Case design allows surface or rear panel mounting
• Meets American Boat and Yacht Council (ABYC) requirements for battery switches
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
• 7/8" (22.22mm) stud length to accept multiple cable terminals
• Tactile textures indicate knob position by feel only

HD-Series Battery Switch Single Circuit ON/OFF

PN:  3000
600 Amperes Continuous Rating for large diesel engines

• 600 Ampere Continuous Rating
  
• Accepts two 4/0 battery cables per terminal
  
• Ignition protected - safe for installation aboard gasoline powered boats
  
• .870" (22.01mm) stud length to accept multiple cable terminals
  
• 1/2" (M12) Tin-plated copper studs for maximum conductivity and corrosion resistance
  
• Meets American Boat and Yacht Council (ABYC) requirements for battery switches
  
• Tactile textures indicate knob position by feel only
  
• Case design allows surface or rear panel mounting
  
• Fits all Perko and Guest low amperage battery switch hole patterns

HD-Series Battery Switch Single Circuit ON/OFF with AFD

PN:  3001
600 Amperes Continuous Rating for large diesel engines

• 600 Ampere Continuous Rating
  
• Accepts two 4/0 battery cables per terminal
  
• Ignition protected - safe for installation aboard gasoline powered boats
  
• .870" (22.01mm) stud length to accept multiple cable terminals
  
• 1/2" (M12) Tin-plated copper studs for maximum conductivity and corrosion resistance
  
• Meets American Boat and Yacht Council (ABYC) requirements for battery switches
  
• Tactile textures indicate knob position by feel only
  
• Case design allows surface or rear panel mounting
  
• Fits all Perko and Guest low amperage battery switch hole patterns

HD-Series Battery Switch Selector

PN:  3002
500 Amperes Continuous Rating for large diesel engines

• 500 Ampere Continuous Rating
  
• Accepts 4/0 battery cables
  
• Ignition protected - safe for installation aboard gasoline powered boats
  
• .870" (22.01mm) stud length to accept 4 or more cable terminals
  
• 1/2" (M12) Tin-plated copper studs for maximum conductivity and corrosion resistance
  
• Meets American Boat and Yacht Council (ABYC) requirements for battery switches
  
• Tactile textures indicate knob position by feel only
  
• Case design allows surface or rear panel mounting
  
• Fits all Perko and Guest low amperage battery switch hole patterns

HD-Series Battery Switch Selector with Alternator Field Disconnect

PN:  3003
500 Amperes Continuous Rating for large diesel engines

• 500 Ampere Continuous Rating
  
• Accepts 4/0 battery cables
  
• Ignition protected - safe for installation aboard gasoline powered boats
  
• .870" (22.01mm) stud length to accept 4 or more cable terminals
  
• 1/2" (M12) Tin-plated copper studs for maximum conductivity and corrosion resistance
  
• Meets American Boat and Yacht Council (ABYC) requirements for battery switches
  
• Tactile textures indicate knob position by feel only
  
• Case design allows surface or rear panel mounting
  
• Fits all Perko and Guest low amperage battery switch hole patterns

6007
m-Series (Mini) Battery Switch Selector

Make before break contact design allows switching between battery banks without power interruption

Selector

• Switches battery bank 1 or battery bank 2 or both to a single load using one switch

• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface, front panel, or rear panel mounting
  
• Isolating cover with snap-on sections protects rear contacts
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Ideal for marine or RV applications
  
• All non-corrosive marine grade metals
  
• Molded in durable reinforced polycarbonate
  
• Tactile textures indicate knob position by feel only
  
• Label with international ON/OFF legends
  
• Removable key or knob remains positively retained
  
• ICON label set included for circuit identification

6010
m-Series (Mini) Battery Switch

Dual Circuit™

• Switches both positive and negative lines simultaneously with one simple ON/OFF switch meeting European and metal boat requirements for a double pole switch
  
• Switches circuits of different voltages, such as 12 volt and 24 volt, simultaneously with one simple ON/OFF switch

• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface, front panel, or rear panel mounting
  
• Isolating cover with snap-on sections protects rear contacts
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Ideal for marine or RV applications
  
• All non-corrosive marine grade metals
  
• Molded in durable reinforced polycarbonate
  
• Tactile textures indicate knob position by feel only
  
• Label with international ON/OFF legends
  
• Removable key or knob remains positively retained
  
• ICON label set included for circuit identification

6011
m-Series (Mini) Battery Switch

Dual Circuit Plus™

• Switches two battery banks simultaneously with one simple ON/OFF switch while maintaining battery bank isolation, minimizing the risk of a dead Start battery
  
• The "Combine Batteries" function offers the ability to combine the two battery banks in the event of a low Start battery

• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface, front panel, or rear panel mounting
  
• Isolating cover with snap-on sections protects rear contacts
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Ideal for marine or RV applications
  
• All non-corrosive marine grade metals
  
• Molded in durable reinforced polycarbonate
  
• Tactile textures indicate knob position by feel only
  
• Label with international ON/OFF legends
  
• Removable key or knob remains positively retained
  
• ICON label set included for circuit identification

7902
Icon Circuit Identification Label Kit for Battery Switches

• 18 icon labels for battery switches, use to identify circuits
  
• Examples: Battery, Bow Thruster, Chassis Engine, House

5510E
Dual Circuit Battery Switch

• CE Marked
  
• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface or rear panel mounting
  
• Meets American Boat and Yacht Council (ABYC) requirements for battery switches
  
• 3/8" - 16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" stud length to accept multiple cable terminals
  
• Tactile textures indicate knob position by feel only

5511e
Dual Circuit Plus Battery Switch

• CE Marked
  
• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface or rear panel mounting
  
• Meets American Boat and Yacht Council (ABYC) requirements for battery
  switches
  
• 3/8" - 16 tin-plated copper studs for maximum conductivity and
  corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" stud length to accept multiple cable terminals
  
• Tactile textures indicate knob position by feel only

6005
m-Series (Mini) Battery Switch

Single Circuit ON/OFF

• Switches a single battery to a single load group
  
• Multiple switches can be used to manage several isolated circuits including cross connecting for emergency paralleling

• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface, front panel, or rear panel mounting
  
• Isolating cover with snap-on sections protects rear contacts
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Ideal for marine or RV applications
  
• All non-corrosive marine grade metals
  
• Molded in durable reinforced polycarbonate
  
• Tactile textures indicate knob position by feel only
  
• Label with international ON/OFF legends
  
• Removable key or knob remains positively retained
  
• ICON label set included for circuit identification

6006
m-Series (Mini) Battery Switch

Single Circuit ON/OFF

• Switches a single battery to a single load group
  
• Multiple switches can be used to manage several isolated circuits including cross conntecting for emergency paralleling

• Ignition protected - Safe for installation aboard gasoline powered boats
  
• Case design allows surface, front panel, or rear panel mounting
  
• Isolating cover with snap-on sections protects rear contacts
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Ideal for marine or RV applications
  
• All non-corrosive marine grade metals
  
• Molded in durable reinforced polycarbonate
  
• Tactile textures indicate knob position by feel only
  
• Label with international ON/OFF legends
  
• Removable key or knob remains positively retained
  
• ICON label set included for circuit identification

7650
Add a Battery

• A complete two battery bank management solution
  
• Dual Circuit Plus™ Battery Switch isolates engine and house circuits, and combines battery banks for emergency starting
  
• The 120 Amp SI ACR automatic charging relay combines for charging

7610

120 Amp SI-Series Automatic Charging Relay

• Allows temporary isolation of house loads from engine circuit during engine cranking to protect sensitive electronics
• Automatically combines battery banks during the charging cycle and isolates under discharge
• 12/24 Volt auto ranging voltage input
• Waterproof rated IP67 - temporary immersion for 30 minutes
• Ignition protected - safe for installation aboard gasoline powered boats
• Remote LED output indicates relay state away from ACR
• LED light indicates when batteries are combined
• LED blinks in undervoltage lockout and starting lockout
• Supports high-output alternators up to 120 Amperes
• Included with the ADD A BATTERY Dual Circuit System
• Automatically combines battery banks during the charging cycle and isolates under discharge
• Ignition protected - safe for installation aboard gasoline-powered boats
• Activates from any charging source - alternators, battery chargers, or solar panels
• Hermetically sealed contacts / vaporproof
• Side and bottom knockouts for power cable connections
• Clip-on cover protects and insulates terminal connections
• Tin-plated copper studs for maximum corrosion resistance
• 7/8" (22.22mm) stud length to accept multiple cable terminals
• 1/4" x 0.031" male quick connect terminals for ground and remote LED and starting interrupt

7620

Manual Control: No
Coil Voltage: 12V DC

• Combines battery banks during charging and isolates under discharge
  
• 500 Ampere continuous rating suitable for use with large battery banks, starters, alternators, and inverter/chargers
  
• Includes ML-Series Remote Control Contura Switch PN 2146
  
• Silver alloy contacts provide high reliability
  
• 3/8" copper studs, using Blue Sea Systems superior one piece stud technology, suitable for 300 Ampere continuous rating and large cable connections

7621

Manual Control: No
Coil Voltage: 24V DC

• Combines battery banks during charging and isolates under discharge
  
• 500 Ampere continuous rating suitable for use with large battery banks, starters, alternators, and inverter/chargers
  
• Can be remotely combined with optional switch
  
• Silver alloy contacts provide high reliability
  
• 3/8" copper studs, using Blue Sea Systems superior one piece stud technology, suitable for 300 Ampere continuous rating and large cable connections

7700

• Includes ML-Series Remote Control Contura Switch 2145
  
• Manual control switch provides an added level of safety allowing control with or without power, and offering "Locked Off" capability for servicing
  
• 500 Ampere continuous rating for engine, inverter, house loads, and emergency battery combine
  
• Magnetic latching draws no current in "ON" or "OFF" state, only draws current when changing state of switch
  
• Silver alloy contacts provides high reliability for switching live loads
  
• 3/8" -16 tin-plated copper studs for maximum conductivity and corrosion resistance
  
• 7/8" (22mm) stud length accepts multiple cable terminals
  
• Label recesses for circuit identification
  

7701

Manual Control: No
Coil Voltage: 12V DC

• 500 Ampere continuous rating for use as a remote battery switch for inboard gasoline or diesel engines, reducing long cable runs
  
• Magnetic latch only draws current when changing state of switch, drawing no current in "ON" or "OFF" state
  
• Silver alloy contacts provides high reliability for switching live loads
• Optional manual switch provides an added level of safety allowing control with or without power, and offering lockout capability for servicing
• 3/8" copper studs, using Blue Sea Systems superior one piece technology, suitable for 300 Amperes continuous rating and large cable connections

7702

Manual Control: Yes
Coil Voltage: 24V DC

• 500 Ampere continuous rating for use as a remote battery switch for inboard gasoline or diesel engines, reducing long cable runs
  
• Magnetic latch only draws current when changing state of switch, drawing no current in "ON" or "OFF" state
  
• Silver alloy contacts provides high reliability for switching live loads
• Optional manual switch provides an added level of safety allowing control with or without power, and offering lockout capability for servicing
• 3/8" copper studs, using Blue Sea Systems superior one piece technology, suitable for 300 Amperes continuous rating and large cable connections

7703

Manual Control: No
Coil Voltage: 24V DC

• 500 Ampere continuous rating for use as a remote battery switch for inboard gasoline or diesel engines, reducing long cable runs
  
• Magnetic latch only draws current when changing state of switch, drawing no current in "ON" or "OFF" state
  
• Silver alloy contacts provides high reliability for switching live loads
• Optional manual switch provides an added level of safety allowing control with or without power, and offering lockout capability for servicing
• 3/8" copper studs, using Blue Sea Systems superior one piece technology, suitable for 300 Amperes continuous rating and large cable connections

7622

Manual Control: Yes
Coil Voltage: 12v

Features:

• Manual control switch provides an added level of safety allowing control with or without power, and offering "Locked Off" capability for servicing
  
• Includes ML-Series Remote Control Contura Switch PN 2146
  
• 500 Ampere continuous rating
  
• Magnetic Latch (ML)-ACR draws very low current (<10 mA to monitor terminal voltage) in the "ON" or "OFF" states, and draws moderate current for very short time when changing state
  
• Start Isolation (SI)-Can be configured for temporary isolation of House loads from Engine circuit during engine cranking to protect sensitive electronics
  
• Engine Isolation (EI)-Can be configured for isolation of two engines while both are running to protect engine electronics and maximize alternator output
  
• Senses charging on two battery banks
  
• Supports high-output alternators up to 500 Amps
  
• LED output to remotely indicate when batteries are combined, isolated, in voltage lockout, in Start or Engine isolation
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance
  
• 7/8" (22mm) stud length accepts multiple cable terminals
  
• Label recesses for circuit protection
  
• Silver alloy contacts provide high reliability for switching live loads

7623

Manual Control: Yes
Coil Voltage: 24v

Features:

• Manual control switch provides an added level of safety allowing control with or without power, and offering "Locked Off" capability for servicing
  
• Includes ML-Series Remote Control Contura Switch PN 2146
  
• 500 Ampere continuous rating
  
• Magnetic Latch (ML)-ACR draws very low current (<10 mA to monitor terminal voltage) in the "ON" or "OFF" states, and draws moderate current for very short time when changing state
  
• Start Isolation (SI)-Can be configured for temporary isolation of House loads from Engine circuit during engine cranking to protect sensitive electronics
  
• Engine Isolation (EI)-Can be configured for isolation of two engines while both are running to protect engine electronics and maximize alternator output
  
• Senses charging on two battery banks
  
• Supports high-output alternators up to 500 Amps
  
• LED output to remotely indicate when batteries are combined, isolated, in voltage lockout, in Start or Engine isolation
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance
  
• 7/8" (22mm) stud length accepts multiple cable terminals
  
• Label recesses for circuit protection
  
• Silver alloy contacts provide high reliability for switching live loads

11001

AFD: Yes
Battery Combiner: No

Features:

• Make-before-break contact design allows switching between battery banks without power interruption
  
• CE Marked
  
• Ignition protected-safe for installation aboard gasoline powered boats
  
• Case design allows surface or rear panel mounting
  
• Meets American Boat and Yacht Council (ABYC) requirements for battery switches
  
• 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 3/8" and M10 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Tactile textures indicate knob position by feel only

11003

Features:

• Meets American Boat and Yacht Council (ABYC) requirements for battery switches
  
• Ignition protected safe for installation aboard gasoline powered boats
  
• Case design allows surface or rear panel mounting
  
• Accepts two 4/0 AWG (95mm) battery cables
  
• M12 tin-plated copper studs for maximum conductivity and corrosion resistance, accepts 1/2" and M12 ring terminals
  
• 7/8" (22.22mm) stud length to accept multiple cable terminals
  
• Tactile textures indicate knob position by feel only
  
• Case design allows surface or rear panel mounting

2151

Features:

• New isolated stud design uses standard 5/16" hardware and permits stacking of terminals
  
• Compact, high-amp fuse-Appropriate for DC Main, inverter, windlass, and bow thruster circuit protection
  
• Provides high current protection in tight space constraints
  
• Weatherproof-suitable for small open-cockpit boats and other harsh environments
  
• Insulating cap prevents accidental shorts
  
• Use 5/16" or 3/8" ring terminal

PowerPost High Amperage Cable Connector 1/4" Stud

Part #:  2001

• Connects high amperage cables securely

CableClams

Part #: 1002    Connector Opening (in):   0.63

• Perfect for antenna installation
  
• Waterproof co-axial installation without removing connectors
  
• Save the expense of removing and replacing connectors
  
• Avoid poor connections from removing factory connectors

MiniBus 100 Ampere Common BusBar 5 x 8-32 Screw Terminal

PN:   2304

• Great for limited space applications in electronics cabinets and under dashboards

MiniBus 100 Ampere Common BusBar 4 x 10-32 Stud Terminal

PN:   2305

• Great for limited space applications in electronics cabinets and under dashboards

DualBus 100 Ampere Common BusBars 5 x 8-32 Screw Terminal

PN:  2701

• Combines negative and positive buses on one block

150 Ampere Common BusBar 10 x #8-32 Screw Terminal

PN:   2301

• Stud design provides direct terminal to bus contact for low resistant connection
  
• Stainless steel studs and screws allow high torquing for excellent electrical contact
  
• Tin-plated copper bus for maximum conductivity and resistance to corrosion
  
• UL 94-VO rated (self extinguishing) base material resists high heat
  
• Raised bus provides easy access to multiple wires on a single screw
  
• UL 94-VO rated base material resists high heat
  
• Captive star type lock washers for anti-rotation and eliminate handling of small, easily dropped parts

150 Ampere Common BusBars 4 x 1/4" Stud Terminal

PN:   2303

• Stud design provides direct terminal to bus contact for low resistant connection
  
• Stainless steel studs allow high torquing for excellent electrical contact
  
• Tin-plated copper bus for maximum conductivity and resistance to corrosion
  
• UV 94-VO rated (self extinguishing) base material resists high heat
  
• Press on insulating cover attaches to studs and allows unobstructed wire access

PowerPost High Amperage Cable Connector 3/8" Stud

Part #:   2003 

• Connects high amperage cables securely

PowerPost High Amperage Cable Connector 5/16" Stud

Part #:   2002 

• Connects high amperage cables securely

PowerPost Plus Cable Connector 3/8" Stud

Part #:   2103 

• 150 Ampere bus allows small wire connections at high amperage cable connections

Terminal Block 30 Ampere 6 Circuit

PN:  2506

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 30 Ampere 8 Circuit

PN:  2508

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 30 Ampere 10 Circuit

PN:  2510

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 30 Ampere 12 Circuit

PN:  2512

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block Jumpers

PN:  9217

• Jumpers allow creation of common circuits on independent connectors

CableClams

Part #: 1001     Connector Opening (in):   0.63

• Perfect for antenna installation
  
• Waterproof co-axial installation without removing connectors
  
• Save the expense of removing and replacing connectors
  
• Avoid poor connections from removing factory connectors

CableClams

Part #: 1003    Connector Opening (in):   1.39

• Perfect for antenna installation
  
• Waterproof co-axial installation without removing connectors
  
• Save the expense of removing and replacing connectors
  
• Avoid poor connections from removing factory connectors

DualBus 100 Ampere Common BusBar 10 x 8-32 Screw Terminal

PN:  2702

• Combines negative and positive buses on one block

Terminal Block 20 Ampere 4 Circuit

PN:  2404

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 20 Ampere 6 Circuit

PN:  2406

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

PowerPost High Amperage Cable Connector 1/4" Stud

Part #:   2011 

• Connects high amperage cables securely

PowerPost Plus Cable Connector 1/4" Stud

Part #:   2101 

• 150 Ampere bus allows small wire connections at high amperage cable connections

PowerPost Plus Cable Connector 5/16" Stud

Part #:   2102 

• 150 Ampere bus allows small wire connections at high amperage cable connections

Terminal Block 20 Ampere 2 Circuit

PN:  2402

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 20 Ampere 8 Circuit

PN:  2408

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 20 Ampere 10 Circuit

PN:  2410

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 30 Ampere 2 Circuit

PN:  2502

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 30 Ampere 4 Circuit

PN:  2504

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 65 Ampere 2 Circuit

PN:  2602

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 65 Ampere 4 Circuit

PN:  2604

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 65 Ampere 8 Circuit

PN:  2608

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block 65 Ampere 10 Circuit

PN:  2610

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

Terminal Block Jumpers

PN:  9216

• Jumpers allow creation of common circuits on independent connectors

Terminal Block Jumpers

PN:  9218

• Jumpers allow creation of common circuits on independent connectors

DualBus Plus 5/16" Stud, 5x10-32 Screw Terminal

PN:  2723

• Combines negative and positive buses on one block
  
• Clear polycarbonate cover snaps on to meet Coast Guard and ABYC insulation requirements

PowerPost High Amperage Cable Connector #10 Stud

Part #:   2010 

• Connects high amperage cables securely

150 Ampere Common BusBar 10 x #8-32 Screw Terminal with Cover

PN:   2300

• Stud design provides direct terminal to bus contact for low resistant connection
  
• Stainless steel studs and screws allow high torquing for excellent electrical contact
  
• Tin-plated copper bus for maximum conductivity and resistance to corrosion
  
• UL 94-VO rated (self extinguishing) base material resists high heat
  
• Press on insulating cover attaches to studs and allows unobstructed wire access
  
• Raised bus provides easy access to multiple wires on a single screw

MiniBus 100 Ampere Common BusBar Grounding BusBar 6 x 8-32 Screw Terminal

PN:   2306

• Great for limited space applications in electronics cabinets and under dashboards

Terminal Block 65 Ampere 6 Circuit

PN:  2606

• Closed back design completely insulates power from the mounting surface
  
• Each screw pair is 1 isolated circuit
  
• Jumpers allow creation of common circuits

DualBus Plus 1/4" Stud, 5x10-32 Screw Terminal

PN:  2722

• Combines negative and positive buses on one block
  
• Clear polycarbonate cover snaps on to meet Coast Guard and ABYC insulation requirements

CableCap Stud Insulator

Cable Size:	18-10
Color	Red

• Insulate stud type connectors on alternators, starters, windlasses and other high amperage devices

CableCap Stud Insulator

Cable Size:	18-10
Color	Black

• Insulate stud type connectors on alternators, starters, windlasses and other high amperage devices

4010
CableCap Stud Insulator

Cable Size:	8-4
Color	Red

• Insulate stud type connectors on alternators, starters, windlasses
  and other high amperage devices

4011
CableCap Stud Insulator

Cable Size:	8-4
Color	Black

• Insulate stud type connectors on alternators, starters, windlasses
  and other high amperage devices

4012
CableCap Stud Insulator

Cable Size:	2-2/0
Color	Red

• Insulate stud type connectors on alternators, starters, windlasses
  and other high amperage devices

4013
CableCap Stud Insulator

Cable Size:	2-2/0
Color	Black

• Insulate stud type connectors on alternators, starters, windlasses
  and other high amperage devices

4014
CableCap Stud Insulator

Cable Size:	3/0-4/0
Color	Red

• Insulate stud type connectors on alternators, starters, windlasses
  and other high amperage devices

4015
CableCap Stud Insulator

Cable Size:	3/0-4/0
Color	Black

• Insulate stud type connectors on alternators, starters, windlasses
  and other high amperage devices

4016
Automotive CableCaps

Cable Size:	4, 2, 1
Color	Red/Black

• Designed to fit standard automotive posts

4017
Automotive CableCaps

Cable Size:	1/0, 2/0
Color	Red/Black

• Designed to fit standard automotive posts

150 Ampere Common Busbar 20 x 8-32 Screw Terminal with Cover

PN:   2312

• Stud design provides direct terminal to bus contact for low resistant connection
  
• Stainless steel studs and screws allow high torquing for excellent electrical contact
  
• Tin-plated copper bus for maximum conductivity and resistance to corrosion
  
• UL 94-VO rated (self extinguishing) base material resists high heat
  
• Press on insulating cover attaches to studs and allows unobstructed wire access
  
• Raised bus provides easy access to multiple wires on a single screw

MiniBus 100 Ampere Common BusBar 5 x 8-32 Screw Terminal with Cover

PN:   2314

• Great for limited space applications in electronics cabinets and under dashboards
  
• Snap on insulating cover attaches to studs and allows unobstructed wire access
  
• Raised bus provides easy access to multiple wires on a single screw
  
• Pressed on busbar eliminates the need for securing nut
  
• Stainless steel studs allow high torquing for excellent electrical contact
  
• Tin-plated copper bus for maximum conductivity and corrosion resistance
  
• Recessed mounting holes eliminate accidental shorts to aluminum and steel mounting surfaces
  
• Captive star type lock washers meet CE requirements for anti-rotation and eliminate handling of small, easily dropped parts
  
• Stainless steel phillips screws for easier installation and resistance to stripping
  
• UL 94-VO rated base material resists high heat

MiniBus 100 Ampere Common BusBar 4 x 10-32 Stud Terminal with Cover

PN:  2315

• Great for limited space applications in electronics cabinets and under dashboards
  
• Snap on insulating cover attaches to studs and allows unobstructed wire access
  
• Raised bus provides easy access to multiple wires on a single screw
  
• Pressed on busbar eliminates the need for a securing nut
  
• Stainless steel studs allow high torquing for excellent electrical contact
  
• Tin-plated copper bus for maximum conductivity and corrosion resistance
  
• Recessed mounting holes eliminate accidental shorts to aluminum and steel mounting surfaces
  
• Captive star type lock washers meet CE requirements for anti-rotation and eliminate handling of small, easily dropped parts
  
• Stainless steel phillips screws for easier installation and resistance to stripping
  
• UL 94-VO rated base material resists high heat

Dual PowerPost Connectors

• Designed for connecting high amp conductors
  
• Includes one black and one red insulator

Dual PowerPost Connectors

• Designed for connecting high amp conductors
  
• Includes one black and one red insulator

Dual PowerPost Connectors

• Designed for outboard engine installation when factory cables need to be extended
  
• Includes one black and one red insulator

PowerBar Common BusBar

Terminal Studs: 2x3/8"-16

• Provides compact high-ampere busing with 3/8" terminal studs

5503

• Stainless steel studs provide resistance to corrosion and high torque for excellent electrical contact
  
• Insert molded studs ensure secure fuse mounting
  
• For use on systems up to 32 Volts DC
  
• Large studs accept cables up to 4/0 AWG
  
• Insulating cover satisfies ABYC/USCG requirements and cover breakouts allow access in any direction
  
• For use on systems up to 32 Volts DC
  
• Large 5/16"-18 studs accept 5/16" (M8) ring terminals, 14 AWG to 2/0 AWG wire

4005
Standard CableCaps

Cable Size - 4, 2, 1
Pair - Red/Black

• For batteries with marine adaptor terminals added on

4006
Large CableCaps

Cable Size - 1/0, 2/0
Pair - Red/Black

• For batteries with marine adaptor terminals added on

A-Series Toggle Double Pole

PN: 7234
Poles: 2
Color: Black
Amperage: 15A

Features:

• Meets American Boat and Yacht Council (ABYC) standards
  
• UL 1077 recognized, TUV certified, CE marked for Europe and CSA certified for Canada
  
• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Used as AC Main circuit protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

AC / DC Single Pole Magnetic World Circuit Breaker

The World Circuit Breaker meets all American Boat and Yacht Council (ABYC) Standards, is UL 1077 Recognized, TUV Certified, CE marked for Europe, and CSA Certified for Canada.

PN:   7208
Color:   Black
Amperage:   15 Amp
Delay:   Standard

Features:

• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Single pole Quick Trip models are designed specifically for electronics protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

AC / DC Single Pole Magnetic World Circuit Breaker

The World Circuit Breaker meets all American Boat and Yacht Council (ABYC) Standards, is UL 1077 Recognized, TUV Certified, CE marked for Europe, and CSA Certified for Canada.

PN:   7202
Color:   White
Amperage:   5 Amp
Delay:   Standard

Features:

• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Single pole Quick Trip models are designed specifically for electronics protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

AC / DC Single Pole Magnetic World Circuit Breaker

The World Circuit Breaker meets all American Boat and Yacht Council (ABYC) Standards, is UL 1077 Recognized, TUV Certified, CE marked for Europe, and CSA Certified for Canada.

PN:   7206
Color:   White
Amperage:   10 Amp
Delay:   Standard

Features:

• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Single pole Quick Trip models are designed specifically for electronics protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

AC / DC Single Pole Magnetic World Circuit Breaker

The World Circuit Breaker meets all American Boat and Yacht Council (ABYC) Standards, is UL 1077 Recognized, TUV Certified, CE marked for Europe, and CSA Certified for Canada.

PN:   7218
Color:   White
Amperage:   25 Amp
Delay:   Standard

Features:

• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Single pole Quick Trip models are designed specifically for electronics protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

AC / DC Single Pole Magnetic World Circuit Breaker

The World Circuit Breaker meets all American Boat and Yacht Council (ABYC) Standards, is UL 1077 Recognized, TUV Certified, CE marked for Europe, and CSA Certified for Canada.

PN:   7226
Color:   White
Amperage:   40 Amp
Delay:   Standard

Features:

• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Single pole Quick Trip models are designed specifically for electronics protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

AC / DC Single Pole Magnetic World Circuit Breaker

The World Circuit Breaker meets all American Boat and Yacht Council (ABYC) Standards, is UL 1077 Recognized, TUV Certified, CE marked for Europe, and CSA Certified for Canada.

PN:   7230
Color:   White
Amperage:   50 Amp
Delay:   Standard

Features:

• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Single pole Quick Trip models are designed specifically for electronics protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

A-Series Toggle Double Pole

PN: 7233
Poles: 2
Color: White
Amperage: 10A

Features:

• Meets American Boat and Yacht Council (ABYC) standards
  
• UL 1077 recognized, TUV certified, CE marked for Europe and CSA certified for Canada
  
• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Used as AC Main circuit protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

A-Series Toggle Double Pole

PN: 7235
Poles: 2
Color: White
Amperage: 15A

Features:

• Meets American Boat and Yacht Council (ABYC) standards
  
• UL 1077 recognized, TUV certified, CE marked for Europe and CSA certified for Canada
  
• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Used as AC Main circuit protection
  
• "Trip Free" design cannot ben held "ON" during fault current condition

A-Series Toggle Double Pole

PN: 7260
Poles: 2
Color: White
Amperage: 20A

Features:

• Meets American Boat and Yacht Council (ABYC) standards
  
• UL 1077 recognized, TUV certified, CE marked for Europe and CSA certified for Canada
  
• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Used as AC Main circuit protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

A-Series Toggle Double Pole

PN: 7238
Poles: 2
Color: White
Amperage: 30A

Features:

• Meets American Boat and Yacht Council (ABYC) standards
  
• UL 1077 recognized, TUV certified, CE marked for Europe and CSA certified for Canada
  
• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Used as AC Main circuit protection
  
• "Trip Free" design cannot ben held "ON" during fault current condition

A-Series Toggle Double Pole

PN: 7240
Poles: 2
Color: White
Amperage: 40A

Features:

• Meets American Boat and Yacht Council (ABYC) standards
  
• UL 1077 recognized, TUV certified, CE marked for Europe and CSA certified for Canada
  
• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Used as AC Main circuit protection
  
• "Trip Free" design cannot ben held "ON" during fault current condition

A-Series Toggle Double Pole

PN: 7242
Poles: 2
Color: White
Amperage: 50A

Features:

• Meets American Boat and Yacht Council (ABYC) standards
  
• UL 1077 recognized, TUV certified, CE marked for Europe and CSA certified for Canada
  
• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Used as AC Main circuit protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

Mounting Panel - Single Pole

• Mounts A-Series Single Pole Toggle Circuit Breakers
  
• Slate gray matches standard panel color
  
• Mounts A-Series double pole toggle circuit breaker
  
• 1/8" aluminum 5052 alloy
  
• Accepts Blue Sea Systems’ label
  
• "Power On" and "Reverse Polarity" LEDs

Hi - Amp Circuit Breaker Trim Bezel

PN:  7198

Features:

• Trim bezel for 285-series Panel Mount Circuit Breaker

AC / DC Single Pole Magnetic World Circuit Breaker

The World Circuit Breaker meets all American Boat and Yacht Council (ABYC) Standards, is UL 1077 Recognized, TUV Certified, CE marked for Europe, and CSA Certified for Canada.

PN:   7210
Color:   White
Amperage:   15 Amp
Delay:   Standard

Features:

• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Single pole Quick Trip models are designed specifically for electronics protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

AC / DC Single Pole Magnetic World Circuit Breaker

The World Circuit Breaker meets all American Boat and Yacht Council (ABYC) Standards, is UL 1077 Recognized, TUV Certified, CE marked for Europe, and CSA Certified for Canada.

PN:   7214
Color:   White
Amperage:   20 Amp
Delay:   Standard

Features:

• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Single pole Quick Trip models are designed specifically for electronics protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

AC / DC Single Pole Magnetic World Circuit Breaker

The World Circuit Breaker meets all American Boat and Yacht Council (ABYC) Standards, is UL 1077 Recognized, TUV Certified, CE marked for Europe, and CSA Certified for Canada.

PN:   7222
Color:   White
Amperage:   30 Amp
Delay:   Standard

Features:

• The industry standard circuit breaker for Blue Sea Systems electrical panels
  
• Combines switching and circuit protection into a single device
  
• Single pole Quick Trip models are designed specifically for electronics protection
  
• "Trip Free" design cannot be held "ON" during fault current condition

187 - Series Thermal Circuit Breakers - Panel Mount

25 Amp Circuit Breaker

PN:  7035

Features:

• Combines switching and circuit protection into a single device
  
• All components meet SAE J1171 external ignition protection requirements
  
• Clear, single lever operation
  
• "Trip Free" design cannot be held "ON" during fault current condition
  
• Waterproof
  
• Recessed mounting holes for clean appearance
  
• Self-trimming case eliminates the need for mounting panels or trim bezels
  
• Round case permits easy installation with standard sized hole saw
  
• Large clearance around terminal studs accept heavy gauge wire lugs
  
• Robust 5/16 terminals provide high torque connections
  
• Large lever with vertical/horizontal orientation provides indication of trip status
  
• Ignition protected - safe for installation aboard gasoline powered boats