MX7000CR

Adjustable Angle holders MX7000CR (1-1/2" ID) are our strongest and most versatile holders. The three point mounting distributes the stress and provides side support. This heavy duty unit allows you to set your outrigger angle for maximum efficiency. The angle is set by positioning the clamp on the main tube during installation. The main tube of this unit is designed to accept the outrigger in either end so the holder can be mounted above or below any flat surface. A fast pin can be substituted for the bolt connecting the clamp to the wing for bridge laydown capability. Approximate area required for mounting is 14-1/2" x 18".

Recomended poles for MX7000CR
AO8716CR - 16 ft Center Rigger (Mk II)
AO8718CR - 18 ft Center Rigger (Mk II)
MX8712CR - 12 ft MX Step- Tube Style
MX8715CR - 15 ft MX Step- Tube Style
MX8718CR - 18 ft MX Step- Tube Style
MX8716CX - 16 ft MX Step- Tube Style - Single Spreader
MX8720CX - 20 ft MX Step- Tube Style - Double Spreader

LEE’S CENTER RIGGER HOLDER 1.75 OD X 1.5 ID BRIGHT SILVER

LEE’S 12’ BRIGHT SILVER POLE W BLACK SPIKE STEP TUBE 1 3/8"

LEE’S 15’ BRIGHT SILVER POLE W BLACK SPIKE STEP TUBE 1 3/8"

LEE’S 18.5’ BRIGHT SILVER POLE W/ BLACK SPIKE STEP TUBE 1.5"

AL7001CR


The AL7001CR (1-3/8"ID) is the solution for boats with a tower or when a lower angle is desired. It has a slightly larger footprint (4"x 7"). Ruggedly constructed from marine grade anodized aluminum. It can be easily attached above or below the standing platform or any flat surface. It comes in a standard angle of 22 degrees that gives it a low rise. Anodized in Bright Silver it is as strong as it is attractive. It accepts all the same poles as the AL7000 series holders.




LEE’S CENTER RIGGER HOLDER 22 DEGREE 1 3/8" ID BRIGHT SILVER

LEE’S 12’ MKII BRIGHT SILVER POLE W/ BLACK SPIKE 1 3/8" OD

LEE’S 15’ MKII BRIGHT SILVER POLE W/ BLACK SPIKE 1 3/8" OD

Sidewinder Bolt-On Outrigger Mount

Below top operation. Fully locked in Running and 80 degree out Trolling positions. Locks when handle is up or down. Rotates when handle is to the left or right. Fastest Lay-Down on the market. Automatically locks in position when raising or lowering the pole. No knobs to loosen or tighten. Just pull down the Ridged Collar and lower or raise the pole. No ball bearing to rust. Internal Delrin Bushings and Nylon Bearing Surfaces provide smooth operation and prevent metal to metal contact.


LEE’S SIDEWINDER BOLT-IN MOUNT LAY-DOWN VERSION SILVER

LEE’S SIDEWINDER BACKING PLATE FOR BOLT-IN HOLDERS

LEE’S 16’ EXTRA STRONG POLES BRIGHT SILVER SIDEWINDER ONLY

LEE’S 18.5’ BRIGHT SILVER STEP POLES FOR SIDEWINDER ONLY

LEE’S 16’ EXTRA STRONG BRIGHT SILVER STANDARD POLES SIDEWIND

LEE’S 18.5’ BRIGHT SILVER STANDARD POLES F/ SIDEWINDER

LEE’S 16’ EXTRA STRONG BRIGHT SILVER OUTRIGGER POLES 1 3/4"

LEE’S 18.5’ BRIGHT SILVER OUTRIGGER POLES 1 3/4" OD

Single Rig

MC0322RK
Up to 25ft. Outriggers

2 - Hanks Black Braided Line
2 - Black’s Release Clips
2 -1/4in x 12in Tension Cords
2 - Eye Straps with Screws
4 - Snap Swivels
2 - Ball Stops


Release Clips Included

LEE’S SINGLE RIGGING KIT FOR RIGGERS TO 25’ RELEASE INCLUDE

LEE’S CENTER RIGGER RIGGING KIT RELEASE CLIPS INCLUDED

LEE’S DELUXE CENTER RIGGER RIGGING KIT NO RELEASE

LEE’S DELUXE CENTER RIGGER RIGGING KIT BLACK MONO NO CLIP

Single Rig

MC0323LK
Up To 25ft Outriggers

2 - Hanks Black Braided Line
2 -1/4in x 12in Tension Cords
2 - Eye Straps with Screws
4 - Snap Swivels
2 - Ball Stops


Release Clips Not Included

LEE’S DELUXE RIGGING KIT 25’ MAX LENGTH SINGLE RIG

Deluxe Rigging Kit

MC0337LS
Single Rig Up to 37ft.

3 - Hanks Black Braided Line
2 - 5/16in x 12in Tension Cords
4 - Eye Straps with Screws
4 - Snap Swivels
2 - Ball Stops


Release Clips Not Included

LEE’S DELUXE RIGGING KIT 37’ MAX LENGTH SINGLE RIG

Deluxe Rigging Kit

MC0337LS/MO
Single Rig Up to 37ft.

150 feet of Black Mono
2 - 5/16in x 12in Tension Cords
4 - Eye Straps with Screws
4 - Snap Swivels
2 - Ball Stops


Release Clips Not Included

LEE’S DELUXE RIGGING KIT 37’ MAX LENGTH BLACK MONO SINGLE

Deluxe Rigging Kit

MC0337LD
Double Rig Up to 37ft.

6 - Hanks Black Braided Line
2 - 5/16in x 12in Tension Cords
2 - 5/16in x 15in Tension Cords
4 - Eye Straps with Screws
8 - Snap Swivels
4 - Ball Stops



LEE’S DELUXE RIGGING KIT 37’ MAX LENGTH DOUBLE RIG

Deluxe Rigging Kit

MC0337LD/MO
Double Rig Up to 37ft.

300 feet of Black Mono
2 - 5/16in x 12in Tension Cords
2 - 5/16in x 15in Tension Cords
4 - Eye Straps with Screws
8 - Snap Swivels
4 - Ball Stops


Release Clips Not Included



LEE’S DELUXE RIGGING KIT 37’ MAX LENGTH BLACK MONO DOUBLE

LEE’S 15’ BRIGHT SILVER POLE W BLACK SPIKE STEP TUBE 1 1/2"

AL7301CR

Fits 1.050" Pipe

The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.


LEE’S CLAMP ON CENTER RIGGER HOLDER PIPE SIZE #1 1 3/8" ID

AL7302CR

Fits 1.315" Pipe

The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.


LEE’S CLAMP ON CENTER RIGGER HOLDER PIPE SIZE #2 1 3/8" ID

AL7303CR

Fits 1.660" Pipe

The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.

LEE’S CLAMP ON CENTER RIGGER HOLDER PIPE SIZE #3 1 3/8" ID

AL7304CR

Fits 1.900" Pipe

The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.

LEE’S CLAMP ON CENTER RIGGER HOLDER PIPE SIZE #4 1 3/8" ID

LEE’S 16’ MKII BRIGHT SILVER POLE W/ BLACK SPIKE 1 1/2" OD

LEE’S 18’ MKII BRIGHT SILVER POLE W/ BLACK SPIKE 1 1/2" OD

Gunnel Mount Outrigger Holders

OH2016S

Size: 1.75"
Dimensions: 3 1/2 x 6

Attractive, Strong, and Bullet Proof all describe our Gunnel Mount Outrigger Holders. One piece flange construction. Plate, Tube and Bar-Pin are all cast simultaneously for the ultimate in strength. Curved Tube has Solid End Plug with Deep Slots to assure long service and reliability. Tubes are made with Port and Starboard slot orientation to optimize fishing angle. Flange mounts flush with gunnel. When tube is removed, gunnel is unobstructed. Unit has three positions, straight up Running, angled out Trolling and straight back for Bridge Clearing. Originally designed by Lee’s in the 50’s and copied by nearly all our competition. However, no one rivals our durability, fit & finish. Chrome on Brass construction.




LEE’S FLUSH MOUNT 1 3/4" SKIFF OUTRIGGER HOLDER

Side Mount Outrigger Holders

OH2018S

Size: 1.75"
Dimensions: 4 1/2 x 7 1/2

Side Mount Bracket utilizes same curved tube as Gunnel Mount. One piece Bracket construction. Tube, Feet and Bar-Pin are all cast simultaneously for the ultimate in strength. Unit provides same three positions as Flush Mount. Same rugged Chrome on Brass Cosntruction.



LEE’S SIDE MOUNT 1 3/4" SKIFF OUTRIGGER HOLDER

Gunnel Mount Outrigger Holders

Size: 2.0"
Dimensions: 4 x 6 1/2

Attractive, Strong, and Bullet Proof all describe our Gunnel Mount Outrigger Holders. One piece flange construction. Plate, Tube and Bar-Pin are all cast simultaneously for the ultimate in strength. Curved Tube has Solid End Plug with Deep Slots to assure long service and reliability. Tubes are made with Port and Starboard slot orientation to optimize fishing angle. Flange mounts flush with gunnel. When tube is removed, gunnel is unobstructed. Unit has three positions, straight up Running, angled out Trolling and straight back for Bridge Clearing. Originally designed by Lee’s in the 50’s and copied by nearly all our competition. However, no one rivals our durability, fit & finish. Chrome on Brass construction.



LEE’S FLUSH MOUNT 2" SKIFF OUTRIGGER HOLDER

Side Mount Outrigger Holders

OH2020S

Size: 2.0"
Dimensions: 4 3/4 x 7 1/2

Side Mount Bracket utilizes same curved tube as Gunnel Mount. One piece Bracket construction. Tube, Feet and Bar-Pin are all cast simultaneously for the ultimate in strength. Unit provides same three positions as Flush Mount. Same rugged Chrom on Brass Cosntruction.



LEE’S SIDE MOUNT 2" SKIFF OUTRIGGER HOLDER

The Original Wishbone Outrigger Holder

The Original Wishbone Style Outrigger Holder has been in production for over 45 years. Setting the standard for the industry, our "Junior" outrigger holder has often been imitated, but never equaled. Its ease of operation, adjustable fishing angle, ability to lay down for bridges and small footprint makes it the ideal holder for a multitude of boats.

Durability was the watchword at its conception. You won’t find plastic parts in this holder. Constructed of heavy duty brass forgings, heavy wall brass pipe and a stainless steel main tube, it epitomizes strength and reliability. The three point mounting system provides maximum strength and distributes the stress to the mounting surface over a wide area. This holder can be mounted vertically or angled toward the stern. Somewhere between twenty to thirty five degrees is normal.

Model OH226S is for use with our deluxe 19ft. single spreader poles and non-spreader poles up to 22ft.

LEE’S JR OUTRIGGER HOLDERS 2" X 18" MAIN TUBE WISHBONE STYLE

LEE’S 18.5’ BRIGHT SILVER MKII OUTRIGGER POLES 2" OD

LEE’S 19’ EXTRA STRONG BRIGHT SILVER OUTRIGGER POLES 2" OD

TX3916 Outrigger pole is built to the high standards of workmanship you have come to expect from Lee’s Tackle. Our no-compromise design integrates both performance and elegance. It’s efficient at trolling baits, both natural and artificial, and also looks great.

Our new model TX3916 is the perfect companion for our Sidewinder top mount outrigger holder. With an overall length of 16 1/2 plus feet when expanded, it collapses to just 6 feet when compressed. The Tx Series, built from the usual high grade marine materials consistently used at Lee’s Tackle, will give superb performance for many years of serious fishing.

Color: Silver/Black - Pair

LEE’S 16.5’ BRIGHT SILVER BLACK SPIKE TELESCOPIC POLES

Flush Mount Rod Holder

RH-525SS Medium 30° Stainless Steel

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.



LEE’S 30 DEGREE SS FLUSH MOUNT ROD HOLDER MEDIUM 2" OD

Flush Mount Rod Holder

RH-527VS Medium 0° Stainless Steel

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.




LEE’S 0 DEGREE SS FLUSH MOUNT ROD HOLDER MEDIUM 2" OD

Flush Mount Rod Holder

RH-529HS Medium 15° Stainless Steel

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.

LEE’S 15 DEGREE SS FLUSH MOUNT ROD HOLDER MEDIUM 2" OD

Flush Mount Rod Holder

RH-530 Large 30° Stainless Steel

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.


LEE’S 30 DEGREE SS FLUSH MOUNT ROD HOLDER HEAVY DUTY 2.25" OD

Flush Mount Rod Holder

RH-532VS Large 0° Stainless Steel

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.



LEE’S 0 DEGREE SS FLUSH MOUNT ROD HOLDER HEAVY DUTY 2.25" OD

Flush Mount Rod Holder

RH-534HS Large 15° Stainless Steel

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.


LEE’S 15 DEGREE SS FLUSH MOUNT ROD HOLDER HEAVY DUTY 2.25" OD

Flush Mount Rod Holder

Heavy Duty Bar Pin
All Stainless Steel

RH-525SS/XS Medium 30°

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.




LEE’S 30 DEGREE SS FLUSH MOUNT BAR PIN ROD HOLDER MEDIUM

Flush Mount Rod Holder

Heavy Duty Bar Pin
All Stainless Steel

RH-527VS/XS Medium 0°

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.


LEE’S 0 DEGREE SS FLUSH MOUNT BAR PIN ROD HOLDER MEDIUM

Flush Mount Rod Holder

Heavy Duty Bar Pin
All Stainless Steel

RH-529HS/XS Medium 15°

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.


LEE’S 15 DEGREE SS FLUSH MOUNT BAR PIN ROD HOLDER MEDIUM

Flush Mount Rod Holder

Heavy Duty Bar Pin
All Stainless Steel

RH-530SS/XS Large 30°

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.



LEE’S 30 DEGREE SS FLUSH MOUNT BAR PIN ROD HOLDER HEAVY DUTY

Flush Mount Rod Holder

Heavy Duty Bar Pin
All Stainless Steel

RH-532VS/XS Large 0°

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.




LEE’S 0 DEGREE SS FLUSH MOUNT BAR PIN ROD HOLDER HEAVY DUTY

Flush Mount Rod Holder

Heavy Duty Bar Pin
All Stainless Steel

RH-534HS/XS Large 15°

The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years.

LEE’S 15 DEGREE SS FLUSH MOUNT BAR PIN ROD HOLDER HEAVY DUTY

Swivel Base Rod Holders

RH570

Stainless Steel Side Mount w/ Swivel Base

Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.

Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a inch stainless steel lock nut at the bottom of the rod holder.



LEE’S BULKHEAD MOUNT SS SWIVEL BASE ROD HOLDER HEAVY

Swivel Base Rod Holders

RH570XL

Stainless Steel Side Mount w/ Swivel Base Extra Long

This holder is 4" longer than the standard length allowing the bent butt to sit deeper in the holder thus reducing the leverage and stress on the mounting surface.

Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.

Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a ½ inch stainless steel lock nut at the bottom of the rod holder.



LEE’S BULKHEAD MOUNT SS SWIVEL BASE ROD HOLDER EXTRA LONG

Swivel Base Rod Holders

RH575

Standard Angle 30°

Stainless Steel Flush Mount w/ Swivel Base

Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.

Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a ½ inch stainless steel lock nut at the bottom of the rod holder.


LEE’S 30 DEGREE SS FLUSH MOUNT SWIVEL BASE ROD HOLDER 2.25"

Swivel Base Rod Holders

RH575XL

Standard Angle 30°

Stainless Steel Flush Mount w/ Swivel Base Extra Long

This holder is 4" longer than the standard length allowing the bent butt to sit deeper in the holder thus reducing the leverage and stress on the mounting surface.

Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.

Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a ½ inch stainless steel lock nut at the bottom of the rod holder.



LEE’S 30 DEGREE SS FLUSH MOUNT SWIVEL ROD HOLDER EXTRA LONG

Swivel Base Rod Holder

RH577V

Vertical 0°

Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.

Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a ½ inch stainless steel lock nut at the bottom of the rod holder.


LEE’S 0 DEGREE SS FLUSH MOUNT SWIVEL BASE ROD HOLDER 2.25"

Swivel Base Rod Holder

RH577XL

Vertical 0° Extra Long Tube

Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.

Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a ½ inch stainless steel lock nut at the bottom of the rod holder.



LEE’S 0 DEGREE SS FLUSH MOUNT SWIVEL ROD HOLDER EXTRA LONG

Swivel Base Rod Holders

RH579

Half Angle 15°

Stainless Steel Flush Mount w/ Swivel Base

Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.

Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a ½ inch stainless steel lock nut at the bottom of the rod holder.



LEE’S 15 DEGREE SS FLUSH MOUNT SWIVEL BASE ROD HOLDER 2.25"

Swivel Base Rod Holders

RH579XL

Half Angle 15° Extra Long Tube

Stainless Steel Flush Mount w/ Swivel Base

Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.

Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a ½ inch stainless steel lock nut at the bottom of the rod holder.

LEE’S 15 DEGREE SS FLUSH MOUNT SWIVEL ROD HOLDER EXTRA LONG

RH5165

Standard Angle 30° Short Tube

Medium size Short Swivel Base for Stand-Up Rods with Curved Butts. Has 2" OD x 6-1/2" long tube.

Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.

Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a ½ inch stainless steel lock nut at the bottom of the rod holder.


LEE’S 30 DEGREE SS FLUSH MOUNT SWIVEL BASE ROD HOLDER 2"X6.5"

RH5167V

Vertical 0° Short Tube

Medium size Short Swivel Base for Stand-Up Rods with Curved Butts. Has 2" OD x 6-1/2" long tube.

Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.

Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a ½ inch stainless steel lock nut at the bottom of the rod holder.

LEE’S 0 DEGREE SS FLUSH MOUNT SWIVEL BASE ROD HOLDER 2"X6.5"

Swivel Base Rod Holders

RH5169

Half Angle 15° Short Tube

Medium size Short Swivel Base for Stand-Up Rods with Curved Butts. Has 2" OD x 6-1/2" long tube.

Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.

Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a ½ inch stainless steel lock nut at the bottom of the rod holder.





LEE’S 15 DEGREE SS FLUSH MOUNT SWIVEL BASE ROD HOLDER 2"X6.5"

LEE’S PVC DRAIN CAP F/ HEAVY ROD HOLDERS 1/4" NPT FOR BARB

RH5930

Stainless Steel Backing Plate for 30° Heavy Rod Holders



LEE’S SS BACKING PLATE FOR 30 15 0 DEGREE HEAVY ROD HOLDERS

RH5931

Stainless Steel Backing Plate for 30° Medium Rod Holders



LEE’S SS BACKING PLATE FOR 30 DEGREE MEDIUM ROD HOLDERS

RH511

Vinyl Rubber Insert for RH510 & RH527V



LEE’S VINYL RUBBER INSERTS FOR RH510 AND RH527V

RH513

Vinyl Rubber Insert for RH512, RH550, RH552CB & RH552XL



LEE’S VINYL RUBBER INSERTS FOR RH512 RH550 RH552CB RH552XL

RH516

Vinyl Rubber Insert for RH515, RH532 & CH110



LEE’S VINYL RUBBER INSERTS FOR RH515 RH532 CH110

RH526

Vinyl Rubber Insert for RH525



LEE’S VINYL RUBBER INSERTS FOR RH525

RH528

Vinyl Rubber Insert for RH529H



LEE’S VINYL RUBBER INSERTS FOR RH529H

RH531

Vinyl Rubber Insert for RH530



LEE’S VINYL RUBBER INSERTS FOR RH530

RH535

Vinyl Rubber Insert for RH534H



LEE’S VINYL RUBBER INSERTS FOR RH534H

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 12T/LT

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 12T/LT BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 16S

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 16S BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 20

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 20 BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 20T

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 20T BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 30

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 30 BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 30T, 30S

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 30T 30S BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 30VSW, 30TW, 30SW

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 30VSW 30TW 30SW BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 50

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 50 BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 50W

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 50W BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 50T, 50S

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 50T 50S BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 50VSW, 50TW, 50SW

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 50VSW 50TW 50SW BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 70VS

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 70VS BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 80

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 80 BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 80W

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 80W BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 80T,80ST, 80TS

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 80T 80ST 80TS BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 80TW,80SW, 80STW

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 80TW 80SW 80STW BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 130, 130H, 130S

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD / REEL HANGER PENN 130 130H 130S BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Penn International 130ST

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.


LEE’S ROD / REEL HANGER PENN 130ST BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Shimano Tiagra 16

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.


LEE’S ROD/REEL HANGER SHIMANO TIAGRA 16 BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Shimano Tiagra 20

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD/REEL HANGER SHIMANO TIAGRA 20 BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Shimano Tiagra 30

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD/REEL HANGER SHIMANO TIAGRA 30 BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Shimano Tiagra 30W

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD/REEL HANGER SHIMANO TIAGRA 30W BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Shimano Tiagra 50

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD/REEL HANGER SHIMANO TIAGRA 50 BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Shimano Tiagra 50W

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD/REEL HANGER SHIMANO TIAGRA 50W BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Shimano Tiagra 80W

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD/REEL HANGER SHIMANO TIAGRA 80W BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Shimano TDL20

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.


LEE’S ROD/REEL HANGER SHIMANO TLD20 BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Shimano TDL25, TLD30

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD/REEL HANGER SHIMANO TLD25 TLD30 BRIGHT GOLD

Rod Storage Systems
Rod and Reel Hanger Set

Anodized Finish: Gold
For: Shimano TLD50 LRS (2 Speed)

Constructed of Marine Grade Anodized Aluminum Bright Gold. Reel is attached to Hanger by spring loaded pins riding in bracket. Pins snap into harness lugs on top of reel. Reel cannot swing since it is held in upright position. Tip of Rod is placed into Locking End of set and the Nylon Ring is rotated to lock it in. Can be mounted Horizontally, Vertically or Overhead.



LEE’S ROD/REEL HANGER SHIMANO TLD50 LRS BRIGHT GOLD

Rod Storage Systems
Single Rod Rack Sets

Finish: Satin Silver

Simple and efficient rod storage. Constructed of Marine Grade Anodized Aluminum with a variety of Anodized Finishes. Rod Butt is inserted into Closed End of set. Vinyl insert protects the Rod Butt. Tip of rod is placed into Locking End of set and Nylon Locking Ring is rotated to lock it in. Will support the heaviest of rods. Can be mounted Horizontally, Vertically or Overhead.



LEE’S SINGLE ROD RACK SET SATIN SILVER

Rod Storage Systems
Single Rod Rack Sets

Anodized Finish: Bright Gold

Simple and efficient rod storage. Constructed of Marine Grade Anodized Aluminum with a variety of Anodized Finishes. Rod Butt is inserted into Closed End of set. Vinyl insert protects the Rod Butt. Tip of rod is placed into Locking End of set and Nylon Locking Ring is rotated to lock it in. Will support the heaviest of rods. Can be mounted Horizontally, Vertically or Overhead.



LEE’S SINGLE ROD RACK SET BRIGHT GOLD

Rod Storage Systems
Single Rod Rack Sets

Anodized Finish: Bright Gold

Simple and efficient rod storage. Constructed of Marine Grade Anodized Aluminum with a variety of Anodized Finishes. Rod Butt is inserted into Closed End of set. Vinyl insert protects the Rod Butt. Tip of rod is placed into Locking End of set and Nylon Locking Ring is rotated to lock it in. Will support the heaviest of rods. Can be mounted Horizontally, Vertically or Overhead.



LEE’S SINGLE ROD RACK SET BRIGHT SILVER

Aluminum Clamp-on Rod Holders

Model:  RA5001SL
Color:   Sliver
Fits:      1.050" O.D. Pipe
Mount:  Vertical


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER SLVR ALUMINUM VERTICAL PIPE SIZE #1

Aluminum Clamp-on Rod Holders

Model:  RA5001GL
Color:   Gold
Fits:      1.050" O.D. Pipe
Mount:  Vertical


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER GOLD ALUMINUM VERTICAL PIPE SIZE #1

Aluminum Clamp-on Rod Holders

Model:  RA5002SL
Color:   Silver
Fits:      1.315" O.D. Pipe
Mount:  Vertical


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER SLVR ALUMINUM VERTICAL PIPE SIZE #2

Aluminum Clamp-on Rod Holders

Model:  RA5003SL
Color:   Silver
Fits:      1.660" O.D. Pipe
Mount:  Vertical


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER SLVR ALUMINUM VERTICAL PIPE SIZE #3

Aluminum Clamp-on Rod Holders

Model:  RA5003GL
Color:   Gold
Fits:      1.660" O.D. Pipe
Mount:  Vertical


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.

LEE’S CLAMP-ON ROD HOLDER GOLD ALUMINUM VERTICAL PIPE SIZE #3

Aluminum Clamp-on Rod Holders

Model:  RA5004SL
Color:   Silver
Fits:      1.900" O.D. Pipe
Mount:  Vertial


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER SLVR ALUMINUM VERTICAL PIPE SIZE #4

Aluminum Clamp-on Rod Holders

Model:  RA5004GL
Color:   Gold
Fits:      1.900" O.D. Pipe
Mount:  Vertial


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER GOLD ALUMINUM VERTICAL PIPE SIZE #4

Aluminum Clamp-on Rod Holders

Model:  RA5005SL
Color:   Silver
Fits:      2.375" O.D. Pipe
Mount:  Vertial


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.

LEE’S CLAMP-ON ROD HOLDER SLVR ALUMINUM VERTICAL PIPE SIZE #5

Aluminum Clamp-on Rod Holders

Model:  RA5005GL
Color:   Gold
Fits:      2.375" O.D. Pipe
Mount:  Vertial


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.

LEE’S CLAMP-ON ROD HOLDER GOLD ALUMINUM VERTICAL PIPE SIZE #5

Aluminum Clamp-on Rod Holders

Model:  RA5201SL
Color:   Silver
Fits:      1.050" O.D. Pipe
Mount:  Horizontal


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER SLVR ALUM HORIZONTAL PIPE SIZE #1

Aluminum Clamp-on Rod Holders

Model:  RA5201GL
Color:   Gold
Fits:      1.050" O.D. Pipe
Mount:  Horizontal


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER GOLD ALUM HORIZONTAL PIPE SIZE #1

Aluminum Clamp-on Rod Holders

Model:  RA5202SL
Color:   Silver
Fits:      1.315" O.D. Pipe
Mount:  Horizontal


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER SLVR ALUM HORIZONTAL PIPE SIZE #2

Aluminum Clamp-on Rod Holders

Model:  RA5202GL
Color:   Gold
Fits:      1.315" O.D. Pipe
Mount:  Horizontal


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER GOLD ALUM HORIZONTAL PIPE SIZE #2

Aluminum Clamp-on Rod Holders

Model:  RA5203SL
Color:   Silver
Fits:      1.660" O.D. Pipe
Mount:  Horizontal


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER SLVR ALUM HORIZONTAL PIPE SIZE #3

Aluminum Clamp-on Rod Holders

Model:  RA5203GL
Color:   Gold
Fits:      1.660" O.D. Pipe
Mount:  Horizontal


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER GOLD ALUM HORIZONTAL PIPE SIZE #3

Aluminum Clamp-on Rod Holders

Model:  RA5204SL
Color:   Silver
Fits:      1.900" O.D. Pipe
Mount:  Horizontal


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER SLVR ALUM HORIZONTAL PIPE SIZE #4

Aluminum Clamp-on Rod Holders

Model:  RA5204GL
Color:   Gold
Fits:      1.900" O.D. Pipe
Mount:  Horizontal


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER GOLD ALUM HORIZONTAL PIPE SIZE #4

Aluminum Clamp-on Rod Holders

Model:  RA5205SL
Color:   Silver
Fits:      2.375" O.D. Pipe
Mount:  Horizontal


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.


LEE’S CLAMP-ON ROD HOLDER SLVR ALUM HORIZONTAL PIPE SIZE #5

Aluminum Clamp-on Rod Holders

Model:  RA5205GL
Color:   Gold
Fits:      2.375" O.D. Pipe
Mount:  Horizontal


JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don’t like the position, simply move them.

These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe.

All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.

LEE’S CLAMP-ON ROD HOLDER GOLD ALUM HORIZONTAL PIPE SIZE #5

Swivel Base Flush Mount Rod Holder
Part #: RH-5365SS
Medium 30 Stainless Steel

Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip’s roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a half inch stainless steel lock nut at the bottom of the rod holder.

LEE’S 30 DEGREE SS FLUSH MOUNT SWIVEL BASE ROD HOLDER 2"X9"

Swivel Base Flush Mount Rod Holder
Part #: RH-5367SS
Medium 0 Degree Stainless Steel

Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip’s roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a half inch stainless steel lock nut at the bottom of the rod holder.

LEE’S 0 DEGREE SS FLUSH MOUNT SWIVEL BASE ROD HOLDER 2"X9"

Swivel Base Flush Mount Rod Holder
Part #: RH-5367SS
Medium 0 Degree Stainless Steel

Without a doubt, our swivel base rod holder is the "Ultimate Rod Holder" for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tip’s roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a half inch stainless steel lock nut at the bottom of the rod holder.

LEE’S 15 DEGREE SS FLUSH MOUNT SWIVEL BASE ROD HOLDER 2"X9"

Clamp-On Accessory

Fits: 1.050" Pipe
Mounts: Horizontal
Finish: Silver

Heavy duty Clamp-On brackets come ready to mount fixed antennas. These brackets are designed to fit standard size aluminum pipe. Constructed from marine grade aluminum, all brackets are anodized after fabrication for 100% anodized protection. These brackets come standard with bright silver anodized finish. Quickly attached or detached with only an Allen Wrench, they are the perfect retro-fit item.

LEE’S CLAMP ON ANTENNA MOUNT SILVER PIPE SIZE #1 HORIZONTAL

Clamp-On Accessory

Fits: 1.315" Pipe
Mounts: Horizontal
Finish: Silver

Heavy duty Clamp-On brackets come ready to mount fixed antennas. These brackets are designed to fit standard size aluminum pipe. Constructed from marine grade aluminum, all brackets are anodized after fabrication for 100% anodized protection. These brackets come standard with bright silver anodized finish. Quickly attached or detached with only an Allen Wrench, they are the perfect retro-fit item.

LEE’S CLAMP ON ANTENNA MOUNT SILVER PIPE SIZE #2 HORIZONTAL

Clamp-On Accessory

Fits: 1.660" Pipe
Mounts: Horizontal
Finish: Silver

Heavy duty Clamp-On brackets come ready to mount fixed antennas. These brackets are designed to fit standard size aluminum pipe. Constructed from marine grade aluminum, all brackets are anodized after fabrication for 100% anodized protection. These brackets come standard with bright silver anodized finish. Quickly attached or detached with only an Allen Wrench, they are the perfect retro-fit item.

LEE’S CLAMP ON ANTENNA MOUNT SILVER PIPE SIZE #3 HORIZONTAL

Clamp-On Accessory

Fits: 1.900" Pipe
Mounts: Horizontal
Finish: Silver

Heavy duty Clamp-On brackets come ready to mount fixed antennas. These brackets are designed to fit standard size aluminum pipe. Constructed from marine grade aluminum, all brackets are anodized after fabrication for 100% anodized protection. These brackets come standard with bright silver anodized finish. Quickly attached or detached with only an Allen Wrench, they are the perfect retro-fit item.




LEE’S CLAMP ON ANTENNA MOUNT SILVER PIPE SIZE #4 HORIZONTAL

Clamp-On Accessory

Fits: 1.050" Pipe
Mounts: Horizontal/Vertical
Finish: Silver

Heavy duty Clamp-On brackets come ready to mount lights. These brackets are designed to fit standard size aluminum pipe. Constructed from marine grade aluminum, all brackets are anodized after fabrication for 100% anodized protection. These brackets come standard with bright silver anodized finish. Quickly attached or detached with only an Allen Wrench, they are the perfect retro-fit item.

Light Brackets can be mounted on Horizontal or Vertical pipe. They come with five pre-threaded holes for mounting most standard Halogen lights. Two attachment bolts are included with each unit.


LEE’S CLAMP ON LIGHT BRACKET SILVER PIPE SIZE #1 VERT/HORIZ

Clamp-On Accessory

Fits: 1.050" Pipe
Mounts: Horizontal/Vertical
Finish: Silver

Heavy duty Clamp-On brackets come ready to mount lights. These brackets are designed to fit standard size aluminum pipe. Constructed from marine grade aluminum, all brackets are anodized after fabrication for 100% anodized protection. These brackets come standard with bright silver anodized finish. Quickly attached or detached with only an Allen Wrench, they are the perfect retro-fit item.

Light Brackets can be mounted on Horizontal or Vertical pipe. They come with five pre-threaded holes for mounting most standard Halogen lights. Two attachment bolts are included with each unit.


LEE’S CLAMP ON LIGHT BRACKET SILVER PIPE SIZE #2 VERT/HORIZ

Clamp-On Accessory

Fits: 1.660" Pipe
Mounts: Horizontal/Vertical
Finish: Silver

Heavy duty Clamp-On brackets come ready to mount lights. These brackets are designed to fit standard size aluminum pipe. Constructed from marine grade aluminum, all brackets are anodized after fabrication for 100% anodized protection. These brackets come standard with bright silver anodized finish. Quickly attached or detached with only an Allen Wrench, they are the perfect retro-fit item.

Light Brackets can be mounted on Horizontal or Vertical pipe. They come with five pre-threaded holes for mounting most standard Halogen lights. Two attachment bolts are included with each unit.



LEE’S CLAMP ON LIGHT BRACKET SILVER PIPE SIZE #3 VERT/HORIZ

Clamp-On Accessory

Fits: 1.900" Pipe
Mounts: Horizontal/Vertical
Finish: Silver

Heavy duty Clamp-On brackets come ready to mount lights. These brackets are designed to fit standard size aluminum pipe. Constructed from marine grade aluminum, all brackets are anodized after fabrication for 100% anodized protection. These brackets come standard with bright silver anodized finish. Quickly attached or detached with only an Allen Wrench, they are the perfect retro-fit item.

Light Brackets can be mounted on Horizontal or Vertical pipe. They come with five pre-threaded holes for mounting most standard Halogen lights. Two attachment bolts are included with each unit.



LEE’S CLAMP ON LIGHT BRACKET SILVER PIPE SIZE #4 VERT/HORIZ