Power-Pac
Designed for critical applications such as VHF shore stations that must remain on the air, even during a power outage. The 12 volt supply features built-in back-up batteries which are charged during normal operation and then continue to power radios even when AC power is lost.

• Highly regulated, low ripple output for noise-free radio operation
• Battery automatically comes on-line if AC fails
• Low battery alarm and disconnect, with override switch for emergency power

General Specifications

• Input 115/230 VAC, 50-60 Hz.
• Output:13.6 VDC @ 5A cont., 10A Int.
• Regulation: 1% line and load
• Ripple: 1% P-P
• Operating Temp: 0-40° C

Models:
Power-Pac 7 A/H (w/7 amp/hour battery), 18 lbs.
Power-Pac 14 A/H (w/14 amp/hour battery), 24 lbs.
Dimensions (both models): 5.3? H x 9.0? W x 10.5? D

Power-Pac
Designed for critical applications such as VHF shore stations that must remain on the air, even during a power outage. The 12 volt supply features built-in back-up batteries which are charged during normal operation and then continue to power radios even when AC power is lost.

• Highly regulated, low ripple output for noise-free radio operation
• Battery automatically comes on-line if AC fails
• Low battery alarm and disconnect, with override switch for emergency power

General Specifications

• Input 115/230 VAC, 50-60 Hz.
• Output:13.6 VDC @ 5A cont., 10A Int.
• Regulation: 1% line and load
• Ripple: 1% P-P
• Operating Temp: 0-40° C

Models:
Power-Pac 7 A/H (w/7 amp/hour battery), 18 lbs.
Power-Pac 14 A/H (w/14 amp/hour battery), 24 lbs.
Dimensions (both models): 5.3? H x 9.0? W x 10.5? D

Heavy Duty Series

• Designed for powering 12 and 24 VDC communication/navigation equipment aboard commercial vessels where reliability is the primary consideration.
• Input voltage 115 or 230 VAC selected by slide switch on the front panel.
• Excellent Regulation and Ripple Spec: Output voltage maintained within 1% under all line and load conditions within rating; Ripple is less than 40 mV P-P. (12 volt) or 70 mV P-P (24-volt)
• Polyurethane conformal coated PC board and corrosion resistant heavy duty aluminum case with integral shock mounts assures survival in hostile environments
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Supply and Load Circuit Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload and input/output fusing.
• Thermally activated cooling fan on "CD" units.

Specifications

12 Volt Output
115-12-8 Input 115/230 VAC Output 8 amp intermittent 5 amps continuous Dimensions 6.0" h x 4.6" w x 8.5" d wieght 10lbs
115-12-20A Input 115/230 VAC Output 20 amp intermittent 8 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-12-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lbs

24-Volt Output
115-24-10 Input 115/230 VAC Output 10 amp intermittent 4 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-24-18CD Input 115/230 VAC Output 18 amp intermittent 18 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lb
115-24-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 13.0" w x 18.75" d  Weight 60lbs

Output Voltage

12 V Models:
13.6 VDC (Internally adjustable 12.6-14.5 VDC)
Ripple: 40mV P-P ( @ 110-125 / 220-250 VAC input)

24 V Models:
24.5 VDC (Internally adjustable 21-27.5 VDC)
Ripple: 70mV P-P ( @ 110-125 / 220-250 VAC input)

Regulation All Models: 1% Line and Load (@ 110-125 / 220-250 VAC input)

Input Range

105-125/210-250 VAC (selectable), 50-60 Hz
Derate to 50% output below 110 and 220 VAC

Operating Temperature

0-50°C, Derate Linearly From 100% @ 40°C
To 50% @ 50°C Thermal shutdown @ 85°C Case temperature

Duty Cycle

Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 Hours/Day 100% Duty

Heavy Duty Series

• Designed for powering 12 and 24 VDC communication/navigation equipment aboard commercial vessels where reliability is the primary consideration.
• Input voltage 115 or 230 VAC selected by slide switch on the front panel.
• Excellent Regulation and Ripple Spec: Output voltage maintained within 1% under all line and load conditions within rating; Ripple is less than 40 mV P-P. (12 volt) or 70 mV P-P (24-volt)
• Polyurethane conformal coated PC board and corrosion resistant heavy duty aluminum case with integral shock mounts assures survival in hostile environments
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Supply and Load Circuit Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload and input/output fusing.
• Thermally activated cooling fan on "CD" units.

Specifications

12 Volt Output
115-12-8 Input 115/230 VAC Output 8 amp intermittent 5 amps continuous Dimensions 6.0" h x 4.6" w x 8.5" d wieght 10lbs
115-12-20A Input 115/230 VAC Output 20 amp intermittent 8 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-12-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lbs

24-Volt Output
115-24-10 Input 115/230 VAC Output 10 amp intermittent 4 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-24-18CD Input 115/230 VAC Output 18 amp intermittent 18 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lb
115-24-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 13.0" w x 18.75" d  Weight 60lbs

Output Voltage

12 V Models:
13.6 VDC (Internally adjustable 12.6-14.5 VDC)
Ripple: 40mV P-P ( @ 110-125 / 220-250 VAC input)

24 V Models:
24.5 VDC (Internally adjustable 21-27.5 VDC)
Ripple: 70mV P-P ( @ 110-125 / 220-250 VAC input)

Regulation All Models: 1% Line and Load (@ 110-125 / 220-250 VAC input)

Input Range

105-125/210-250 VAC (selectable), 50-60 Hz
Derate to 50% output below 110 and 220 VAC

Operating Temperature

0-50°C, Derate Linearly From 100% @ 40°C
To 50% @ 50°C Thermal shutdown @ 85°C Case temperature

Duty Cycle

Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 Hours/Day 100% Duty

Heavy Duty Series

• Designed for powering 12 and 24 VDC communication/navigation equipment aboard commercial vessels where reliability is the primary consideration.
• Input voltage 115 or 230 VAC selected by slide switch on the front panel.
• Excellent Regulation and Ripple Spec: Output voltage maintained within 1% under all line and load conditions within rating; Ripple is less than 40 mV P-P. (12 volt) or 70 mV P-P (24-volt)
• Polyurethane conformal coated PC board and corrosion resistant heavy duty aluminum case with integral shock mounts assures survival in hostile environments
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Supply and Load Circuit Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload and input/output fusing.
• Thermally activated cooling fan on "CD" units.

Specifications

12 Volt Output
115-12-8 Input 115/230 VAC Output 8 amp intermittent 5 amps continuous Dimensions 6.0" h x 4.6" w x 8.5" d wieght 10lbs
115-12-20A Input 115/230 VAC Output 20 amp intermittent 8 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-12-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lbs

24-Volt Output
115-24-10 Input 115/230 VAC Output 10 amp intermittent 4 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-24-18CD Input 115/230 VAC Output 18 amp intermittent 18 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lb
115-24-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 13.0" w x 18.75" d  Weight 60lbs

Output Voltage

12 V Models:
13.6 VDC (Internally adjustable 12.6-14.5 VDC)
Ripple: 40mV P-P ( @ 110-125 / 220-250 VAC input)

24 V Models:
24.5 VDC (Internally adjustable 21-27.5 VDC)
Ripple: 70mV P-P ( @ 110-125 / 220-250 VAC input)

Regulation All Models: 1% Line and Load (@ 110-125 / 220-250 VAC input)

Input Range

105-125/210-250 VAC (selectable), 50-60 Hz
Derate to 50% output below 110 and 220 VAC

Operating Temperature

0-50°C, Derate Linearly From 100% @ 40°C
To 50% @ 50°C Thermal shutdown @ 85°C Case temperature

Duty Cycle

Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 Hours/Day 100% Duty

Heavy Duty Series

• Designed for powering 12 and 24 VDC communication/navigation equipment aboard commercial vessels where reliability is the primary consideration.
• Input voltage 115 or 230 VAC selected by slide switch on the front panel.
• Excellent Regulation and Ripple Spec: Output voltage maintained within 1% under all line and load conditions within rating; Ripple is less than 40 mV P-P. (12 volt) or 70 mV P-P (24-volt)
• Polyurethane conformal coated PC board and corrosion resistant heavy duty aluminum case with integral shock mounts assures survival in hostile environments
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Supply and Load Circuit Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload and input/output fusing.
• Thermally activated cooling fan on "CD" units.

Specifications

12 Volt Output
115-12-8 Input 115/230 VAC Output 8 amp intermittent 5 amps continuous Dimensions 6.0" h x 4.6" w x 8.5" d wieght 10lbs
115-12-20A Input 115/230 VAC Output 20 amp intermittent 8 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-12-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lbs

24-Volt Output
115-24-10 Input 115/230 VAC Output 10 amp intermittent 4 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-24-18CD Input 115/230 VAC Output 18 amp intermittent 18 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lb
115-24-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 13.0" w x 18.75" d  Weight 60lbs

Output Voltage

12 V Models:
13.6 VDC (Internally adjustable 12.6-14.5 VDC)
Ripple: 40mV P-P ( @ 110-125 / 220-250 VAC input)

24 V Models:
24.5 VDC (Internally adjustable 21-27.5 VDC)
Ripple: 70mV P-P ( @ 110-125 / 220-250 VAC input)

Regulation All Models: 1% Line and Load (@ 110-125 / 220-250 VAC input)

Input Range

105-125/210-250 VAC (selectable), 50-60 Hz
Derate to 50% output below 110 and 220 VAC

Operating Temperature

0-50°C, Derate Linearly From 100% @ 40°C
To 50% @ 50°C Thermal shutdown @ 85°C Case temperature

Duty Cycle

Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 Hours/Day 100% Duty

Heavy Duty Series

• Designed for powering 12 and 24 VDC communication/navigation equipment aboard commercial vessels where reliability is the primary consideration.
• Input voltage 115 or 230 VAC selected by slide switch on the front panel.
• Excellent Regulation and Ripple Spec: Output voltage maintained within 1% under all line and load conditions within rating; Ripple is less than 40 mV P-P. (12 volt) or 70 mV P-P (24-volt)
• Polyurethane conformal coated PC board and corrosion resistant heavy duty aluminum case with integral shock mounts assures survival in hostile environments
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Supply and Load Circuit Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload and input/output fusing.
• Thermally activated cooling fan on "CD" units.

Specifications

12 Volt Output
115-12-8 Input 115/230 VAC Output 8 amp intermittent 5 amps continuous Dimensions 6.0" h x 4.6" w x 8.5" d wieght 10lbs
115-12-20A Input 115/230 VAC Output 20 amp intermittent 8 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-12-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lbs

24-Volt Output
115-24-10 Input 115/230 VAC Output 10 amp intermittent 4 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-24-18CD Input 115/230 VAC Output 18 amp intermittent 18 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lb
115-24-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 13.0" w x 18.75" d  Weight 60lbs

Output Voltage

12 V Models:
13.6 VDC (Internally adjustable 12.6-14.5 VDC)
Ripple: 40mV P-P ( @ 110-125 / 220-250 VAC input)

24 V Models:
24.5 VDC (Internally adjustable 21-27.5 VDC)
Ripple: 70mV P-P ( @ 110-125 / 220-250 VAC input)

Regulation All Models: 1% Line and Load (@ 110-125 / 220-250 VAC input)

Input Range

105-125/210-250 VAC (selectable), 50-60 Hz
Derate to 50% output below 110 and 220 VAC

Operating Temperature

0-50°C, Derate Linearly From 100% @ 40°C
To 50% @ 50°C Thermal shutdown @ 85°C Case temperature

Duty Cycle

Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 Hours/Day 100% Duty

Heavy Duty Series

• Designed for powering 12 and 24 VDC communication/navigation equipment aboard commercial vessels where reliability is the primary consideration.
• Input voltage 115 or 230 VAC selected by slide switch on the front panel.
• Excellent Regulation and Ripple Spec: Output voltage maintained within 1% under all line and load conditions within rating; Ripple is less than 40 mV P-P. (12 volt) or 70 mV P-P (24-volt)
• Polyurethane conformal coated PC board and corrosion resistant heavy duty aluminum case with integral shock mounts assures survival in hostile environments
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Supply and Load Circuit Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload and input/output fusing.
• Thermally activated cooling fan on "CD" units.

Specifications

12 Volt Output
115-12-8 Input 115/230 VAC Output 8 amp intermittent 5 amps continuous Dimensions 6.0" h x 4.6" w x 8.5" d wieght 10lbs
115-12-20A Input 115/230 VAC Output 20 amp intermittent 8 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-12-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lbs

24-Volt Output
115-24-10 Input 115/230 VAC Output 10 amp intermittent 4 amps continuous Dimensions 5.7" h x 4.8" w x 16.3" d  weight 20lbs
115-24-18CD Input 115/230 VAC Output 18 amp intermittent 18 amps continuous Dimensions 6.5" h x 9.5" w x 14.0" d  Weight 32lb
115-24-35CD Input 115/230 VAC Output 35 amp intermittent 35 amps continuous Dimensions 6.5" h x 13.0" w x 18.75" d  Weight 60lbs

Output Voltage

12 V Models:
13.6 VDC (Internally adjustable 12.6-14.5 VDC)
Ripple: 40mV P-P ( @ 110-125 / 220-250 VAC input)

24 V Models:
24.5 VDC (Internally adjustable 21-27.5 VDC)
Ripple: 70mV P-P ( @ 110-125 / 220-250 VAC input)

Regulation All Models: 1% Line and Load (@ 110-125 / 220-250 VAC input)

Input Range

105-125/210-250 VAC (selectable), 50-60 Hz
Derate to 50% output below 110 and 220 VAC

Operating Temperature

0-50°C, Derate Linearly From 100% @ 40°C
To 50% @ 50°C Thermal shutdown @ 85°C Case temperature

Duty Cycle

Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 Hours/Day 100% Duty

Noise Filters
The interference or electronic "noise" generated by alternators, ignition systems, motors, etc., can render a vehicle or vessel’s radio or other electronic equipment virtually useless. This interference takes the form of popping or static on radios or audio gear and garbled images or "hash" on video displays.

These specialized filters can be used singly or in combination to attenuate conducted line noise, either at the affected equipment or at the noise source.

Filtered Frequencies

• Model 150A: 70 kHz - 100 MHz
• Models PC-10 and PC-25: Audio - 200 MHz

Filter Features:

• Heavy duty aluminum construction
• Operate on 6-48 VDC systems
• Integral mounting flanges for secure installation
• Brass stud connectors on alternator filters accommodate high current cables and terminals
• Color coded wire leads on all other models make in-line installation easy

Noise Filters
The interference or electronic "noise" generated by alternators, ignition systems, motors, etc., can render a vehicle or vessel’s radio or other electronic equipment virtually useless. This interference takes the form of popping or static on radios or audio gear and garbled images or "hash" on video displays.

These specialized filters can be used singly or in combination to attenuate conducted line noise, either at the affected equipment or at the noise source.

Filtered Frequencies

• Model 150A: 70 kHz - 100 MHz
• Models PC-10 and PC-25: Audio - 200 MHz

Filter Features:

• Heavy duty aluminum construction
• Operate on 6-48 VDC systems
• Integral mounting flanges for secure installation
• Brass stud connectors on alternator filters accommodate high current cables and terminals
• Color coded wire leads on all other models make in-line installation easy

Noise Filters
The interference or electronic "noise" generated by alternators, ignition systems, motors, etc., can render a vehicle or vessel’s radio or other electronic equipment virtually useless. This interference takes the form of popping or static on radios or audio gear and garbled images or "hash" on video displays.

These specialized filters can be used singly or in combination to attenuate conducted line noise, either at the affected equipment or at the noise source.

Filtered Frequencies

• Model 150A: 70 kHz - 100 MHz
• Models PC-10 and PC-25: Audio - 200 MHz

Filter Features:

• Heavy duty aluminum construction
• Operate on 6-48 VDC systems
• Integral mounting flanges for secure installation
• Brass stud connectors on alternator filters accommodate high current cables and terminals
• Color coded wire leads on all other models make in-line installation easy

Inverter-Chargers

The ?Perfect Wave? Series, these inverter-chargers deliver pure, sinusoidal* AC for flawless operation of all appliances and sensitive electronics. They are ideal for entertainment systems and micro-processor-based equipment such as computers which are intolerant to AC wave distortion.

* except model 2500IC, which produces quasi-sine wave

The circuitry of these Inverter/Chargers incorporates a technology which is field-proven and was carefully refined for years in both harsh industrial and sensitive utility applications. Now this rugged design is offered for marine applications where reliability and performance are paramount, and low noise operation has become a critical factor in the boat owner?s choice of power products.

While incorporating numerous important features these inverter/chargers are engineered with a high functionality approach that installers will appreciate. All connectors and mounts are heavy duty commercial grade.

Called the ?Perfect Wave? Series, these inverter-chargers deliver pure, sinusoidal* AC for flawless operation of all appliances and sensitive electronics. They are ideal for entertainment systems and micro-processor-based equipment such as computers which are intolerant to AC wave distortion.

All models incorporate a built-in automatic transfer switch which activates multi-stage battery charger for rapid and safe replenishment of the inverter battery bank whenever shore or generator AC power is available.

All models feature numerous circuit and safety protections, such as thermally controlled cooling fans, low voltage cutout, thermal and overload protection and ground fault interruption, and are housed in rugged powder coated aluminum cases suitable for permanent horizontal or bulkhead mounting. An optional remote indicator and control panel is available for all models.

* except model 2500IC, which produces quasi-sine wave

Features

• Rugged hostile environment-proven circuitry generates ?Perfect Wave? AC for powering any appliance, from wattage-hungry refrigeration to highly input-sensitive computers, electronic controllers/processors.
• Built-in high output charger for rapid battery bank replenishment? all models feature three stage, temperature compensated charger with output programmable for gel-cell, flooded lead-acid or AGM battery type, and amp-hour capacity selector for proper charging in various applications.
• Internal charger is activated by an automatic transfer relay via remote sensor whenever external AC power is available. Optional Battery Integrator permits charging of multiple banks
• Designed for maximum ease of installation and operation? installer and user-friendly. Large DC input terminal blocks and front panel GFCI protected outlet receptacles. AC output from the inverter may also be hard-wired.
• All important aspects of inverter and charger operation clearly displayed with front panel status indicators-optional remote panel available.
• Numerous safety and circuit protections: short circuit, overload, over-temperature, ground fault protection, output circuit breaker
• Thermally controlled cooling fan prolongs life of components
• Automatic low voltage shutdown circuit prevents damage to batteries due to over-discharge when using inverter function.
• Heavy duty powder coated aluminum construction and polyurethane coated internal circuitry?built to last in the harsh marine environment.
• UL listed with full two year warranty

Specifications

Charger Characteristics:
Three stage ?smart charger?; programmable via selector switch for gel, flooded lead-acid or AGM battery type; temperature compensated. Output voltage temperature compensated via provided battery temp sensor with 20? cable

Case Size
 

Wave Type:
PS = Pure Sine QS = Quasi Sine

Operating Temperature (all models):
-22˚ C to +40˚ C (0˚ F to 104˚F)

Inverter Regulation:120 VAC RMS(110V-127V)

Protection Features (all models):

• Automatic low battery shutdown
• Output circuit breaker
• Auto high temperature shutdown/recovery
• Short circuit protection
• Overload protection

Mechanical Features (all models):

• Thermally controlled cooling fan
• Dual GFCI protected duplex outlet
• AC hard-wire (optional)
• Powder coated aluminum case with shelf or bulkhead mounting flanges
• Polyurethane coated printed circuit boards

• Provide an excellent noise-free RF ground by making direct contact with water outside hull.
• Porous copper construction magnifies contact area ? see matrix for surface area equivalent
• Silicon bronze hardware provided (Not intended for lightning protection)

• Provide an excellent noise-free RF ground by making direct contact with water outside hull.
• Porous copper construction magnifies contact area ? see matrix for surface area equivalent
• Silicon bronze hardware provided (Not intended for lightning protection)

• Provide an excellent noise-free RF ground by making direct contact with water outside hull.
• Porous copper construction magnifies contact area ? see matrix for surface area equivalent
• Silicon bronze hardware provided (Not intended for lightning protection)

Convert 20-50 VDC to 12 or 24 VDC output for powering communication/ navigation equipment, on negative ground systems. (see Isolated series, below for positive ground applications.) Ideal for powering voice, data and navigation transceivers in mobile and marine applications.

• Excellent Regulation: Output voltage maintained within 1% under all line and load conditions within rating.
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Polyurethane conformal coating on PC boards and corrosion-resistant anodized aluminum case with heavy duty shock mounts assure survival in hostile environments.
• Numerous converter and load protection circuits: Current limiting*; automatic thermal shutdown; short circuit proof*; reverse polarity and overvoltage protection*.  Except 3 Amp.
• Carries the CE mark

Isolated series
Same features as Standard Series, but with the additional capability of permitting connection of negative ground gear to positive or floating ground battery systems, or vice-versa. Many models may also be used as 12 or 24 volt stabilizers for highly input voltage sensitive equipment.

Input range:10-56 VDC; positive, negative or floating ground.
Output: 12 or 24 VDC, 3 to 35 amps.

Performance Specifications - Standard & Isolated Series

• Output: 13.6 VDC (internally adjustable 12.6-14.5) or 24.5 VDC (or specify)
• Ripple: 150 mV P-P maximum
• Regulation:
  • Standard: 1% Line/Load
  • Isolated: 2% Line/Load
  • except + 3% Line/Load
• Duty Cycle Ratings*
  • Intermittent - 20 minutes max on time, 20% duty. Current limit set at approx. 105% of intermittent rating
  • Continuous - 24 hours, 100% duty
• Idle Current:
  • Standard Series: Less than 100 mA (including power "ON" light )
  • Isolated Series: approx. 50 mA
• Operating Temp: 0-50° C, Derate Linearly From 100% @ 40° C To 50% @ 50° C Thermal shutdown @ 70° C Case Temperature
• Switching Frequency:
  • Standard: 40 Khz**
  • Isolated: 70Khz
• Efficiency: 85% - Typical.+
• Isolation:
  • Output/Chassis; Input/chassis: 250 VDC
  • Input/Output: 250 VDC (Isolated Series only)
• Certification: Carries the CE mark (Standard Series only)

**except 32-12-3 - Linear, Non-Switching
+except 32-12-3- 50% @ 24 VDC Input

Convert 20-50 VDC to 12 or 24 VDC output for powering communication/ navigation equipment, on negative ground systems. (see Isolated series, below for positive ground applications.) Ideal for powering voice, data and navigation transceivers in mobile and marine applications.

• Excellent Regulation: Output voltage maintained within 1% under all line and load conditions within rating.
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Polyurethane conformal coating on PC boards and corrosion-resistant anodized aluminum case with heavy duty shock mounts assure survival in hostile environments.
• Numerous converter and load protection circuits: Current limiting*; automatic thermal shutdown; short circuit proof*; reverse polarity and overvoltage protection*.  Except 3 Amp.
• Carries the CE mark

Isolated series
Same features as Standard Series, but with the additional capability of permitting connection of negative ground gear to positive or floating ground battery systems, or vice-versa. Many models may also be used as 12 or 24 volt stabilizers for highly input voltage sensitive equipment.

Input range:10-56 VDC; positive, negative or floating ground.
Output: 12 or 24 VDC, 3 to 35 amps.

Performance Specifications - Standard & Isolated Series

• Output: 13.6 VDC (internally adjustable 12.6-14.5) or 24.5 VDC (or specify)
• Ripple: 150 mV P-P maximum
• Regulation:
  • Standard: 1% Line/Load
  • Isolated: 2% Line/Load
  • except + 3% Line/Load
• Duty Cycle Ratings*
  • Intermittent - 20 minutes max on time, 20% duty. Current limit set at approx. 105% of intermittent rating
  • Continuous - 24 hours, 100% duty
• Idle Current:
  • Standard Series: Less than 100 mA (including power "ON" light )
  • Isolated Series: approx. 50 mA
• Operating Temp: 0-50° C, Derate Linearly From 100% @ 40° C To 50% @ 50° C Thermal shutdown @ 70° C Case Temperature
• Switching Frequency:
  • Standard: 40 Khz**
  • Isolated: 70Khz
• Efficiency: 85% - Typical.+
• Isolation:
  • Output/Chassis; Input/chassis: 250 VDC
  • Input/Output: 250 VDC (Isolated Series only)
• Certification: Carries the CE mark (Standard Series only)

**except 32-12-3 - Linear, Non-Switching
+except 32-12-3- 50% @ 24 VDC Input

Convert 20-50 VDC to 12 or 24 VDC output for powering communication/ navigation equipment, on negative ground systems. (see Isolated series, below for positive ground applications.) Ideal for powering voice, data and navigation transceivers in mobile and marine applications.

• Excellent Regulation: Output voltage maintained within 1% under all line and load conditions within rating.
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Polyurethane conformal coating on PC boards and corrosion-resistant anodized aluminum case with heavy duty shock mounts assure survival in hostile environments.
• Numerous converter and load protection circuits: Current limiting*; automatic thermal shutdown; short circuit proof*; reverse polarity and overvoltage protection*.  Except 3 Amp.
• Carries the CE mark

Isolated series
Same features as Standard Series, but with the additional capability of permitting connection of negative ground gear to positive or floating ground battery systems, or vice-versa. Many models may also be used as 12 or 24 volt stabilizers for highly input voltage sensitive equipment.

Input range:10-56 VDC; positive, negative or floating ground.
Output: 12 or 24 VDC, 3 to 35 amps.

Performance Specifications - Standard & Isolated Series

• Output: 13.6 VDC (internally adjustable 12.6-14.5) or 24.5 VDC (or specify)
• Ripple: 150 mV P-P maximum
• Regulation:
  • Standard: 1% Line/Load
  • Isolated: 2% Line/Load
  • except + 3% Line/Load
• Duty Cycle Ratings*
  • Intermittent - 20 minutes max on time, 20% duty. Current limit set at approx. 105% of intermittent rating
  • Continuous - 24 hours, 100% duty
• Idle Current:
  • Standard Series: Less than 100 mA (including power "ON" light )
  • Isolated Series: approx. 50 mA
• Operating Temp: 0-50° C, Derate Linearly From 100% @ 40° C To 50% @ 50° C Thermal shutdown @ 70° C Case Temperature
• Switching Frequency:
  • Standard: 40 Khz**
  • Isolated: 70Khz
• Efficiency: 85% - Typical.+
• Isolation:
  • Output/Chassis; Input/chassis: 250 VDC
  • Input/Output: 250 VDC (Isolated Series only)
• Certification: Carries the CE mark (Standard Series only)

**except 32-12-3 - Linear, Non-Switching
+except 32-12-3- 50% @ 24 VDC Input

Convert 20-50 VDC to 12 or 24 VDC output for powering communication/ navigation equipment, on negative ground systems. (see Isolated series, below for positive ground applications.) Ideal for powering voice, data and navigation transceivers in mobile and marine applications.

• Excellent Regulation: Output voltage maintained within 1% under all line and load conditions within rating.
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Polyurethane conformal coating on PC boards and corrosion-resistant anodized aluminum case with heavy duty shock mounts assure survival in hostile environments.
• Numerous converter and load protection circuits: Current limiting*; automatic thermal shutdown; short circuit proof*; reverse polarity and overvoltage protection*.  Except 3 Amp.
• Carries the CE mark

Isolated series
Same features as Standard Series, but with the additional capability of permitting connection of negative ground gear to positive or floating ground battery systems, or vice-versa. Many models may also be used as 12 or 24 volt stabilizers for highly input voltage sensitive equipment.

Input range:10-56 VDC; positive, negative or floating ground.
Output: 12 or 24 VDC, 3 to 35 amps.

Performance Specifications - Standard & Isolated Series

• Output: 13.6 VDC (internally adjustable 12.6-14.5) or 24.5 VDC (or specify)
• Ripple: 150 mV P-P maximum
• Regulation:
  • Standard: 1% Line/Load
  • Isolated: 2% Line/Load
  • except + 3% Line/Load
• Duty Cycle Ratings*
  • Intermittent - 20 minutes max on time, 20% duty. Current limit set at approx. 105% of intermittent rating
  • Continuous - 24 hours, 100% duty
• Idle Current:
  • Standard Series: Less than 100 mA (including power "ON" light )
  • Isolated Series: approx. 50 mA
• Operating Temp: 0-50° C, Derate Linearly From 100% @ 40° C To 50% @ 50° C Thermal shutdown @ 70° C Case Temperature
• Switching Frequency:
  • Standard: 40 Khz**
  • Isolated: 70Khz
• Efficiency: 85% - Typical.+
• Isolation:
  • Output/Chassis; Input/chassis: 250 VDC
  • Input/Output: 250 VDC (Isolated Series only)
• Certification: Carries the CE mark (Standard Series only)

**except 32-12-3 - Linear, Non-Switching
+except 32-12-3- 50% @ 24 VDC Input

Convert 20-50 VDC to 12 or 24 VDC output for powering communication/ navigation equipment, on negative ground systems. (see Isolated series, below for positive ground applications.) Ideal for powering voice, data and navigation transceivers in mobile and marine applications.

• Excellent Regulation: Output voltage maintained within 1% under all line and load conditions within rating.
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Polyurethane conformal coating on PC boards and corrosion-resistant anodized aluminum case with heavy duty shock mounts assure survival in hostile environments.
• Numerous converter and load protection circuits: Current limiting*; automatic thermal shutdown; short circuit proof*; reverse polarity and overvoltage protection*.  Except 3 Amp.
• Carries the CE mark

Isolated series
Same features as Standard Series, but with the additional capability of permitting connection of negative ground gear to positive or floating ground battery systems, or vice-versa. Many models may also be used as 12 or 24 volt stabilizers for highly input voltage sensitive equipment.

Input range:10-56 VDC; positive, negative or floating ground.
Output: 12 or 24 VDC, 3 to 35 amps.

Performance Specifications - Standard & Isolated Series

• Output: 13.6 VDC (internally adjustable 12.6-14.5) or 24.5 VDC (or specify)
• Ripple: 150 mV P-P maximum
• Regulation:
  • Standard: 1% Line/Load
  • Isolated: 2% Line/Load
  • except + 3% Line/Load
• Duty Cycle Ratings*
  • Intermittent - 20 minutes max on time, 20% duty. Current limit set at approx. 105% of intermittent rating
  • Continuous - 24 hours, 100% duty
• Idle Current:
  • Standard Series: Less than 100 mA (including power "ON" light )
  • Isolated Series: approx. 50 mA
• Operating Temp: 0-50° C, Derate Linearly From 100% @ 40° C To 50% @ 50° C Thermal shutdown @ 70° C Case Temperature
• Switching Frequency:
  • Standard: 40 Khz**
  • Isolated: 70Khz
• Efficiency: 85% - Typical.+
• Isolation:
  • Output/Chassis; Input/chassis: 250 VDC
  • Input/Output: 250 VDC (Isolated Series only)
• Certification: Carries the CE mark (Standard Series only)

**except 32-12-3 - Linear, Non-Switching
+except 32-12-3- 50% @ 24 VDC Input

Convert 20-50 VDC to 12 or 24 VDC output for powering communication/ navigation equipment, on negative ground systems. (see Isolated series, below for positive ground applications.) Ideal for powering voice, data and navigation transceivers in mobile and marine applications.

• Excellent Regulation: Output voltage maintained within 1% under all line and load conditions within rating.
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Polyurethane conformal coating on PC boards and corrosion-resistant anodized aluminum case with heavy duty shock mounts assure survival in hostile environments.
• Numerous converter and load protection circuits: Current limiting*; automatic thermal shutdown; short circuit proof*; reverse polarity and overvoltage protection*.  Except 3 Amp.
• Carries the CE mark

Isolated series
Same features as Standard Series, but with the additional capability of permitting connection of negative ground gear to positive or floating ground battery systems, or vice-versa. Many models may also be used as 12 or 24 volt stabilizers for highly input voltage sensitive equipment.

Input range:10-56 VDC; positive, negative or floating ground.
Output: 12 or 24 VDC, 3 to 35 amps.

Performance Specifications - Standard & Isolated Series

• Output: 13.6 VDC (internally adjustable 12.6-14.5) or 24.5 VDC (or specify)
• Ripple: 150 mV P-P maximum
• Regulation:
  • Standard: 1% Line/Load
  • Isolated: 2% Line/Load
  • except + 3% Line/Load
• Duty Cycle Ratings*
  • Intermittent - 20 minutes max on time, 20% duty. Current limit set at approx. 105% of intermittent rating
  • Continuous - 24 hours, 100% duty
• Idle Current:
  • Standard Series: Less than 100 mA (including power "ON" light )
  • Isolated Series: approx. 50 mA
• Operating Temp: 0-50° C, Derate Linearly From 100% @ 40° C To 50% @ 50° C Thermal shutdown @ 70° C Case Temperature
• Switching Frequency:
  • Standard: 40 Khz**
  • Isolated: 70Khz
• Efficiency: 85% - Typical.+
• Isolation:
  • Output/Chassis; Input/chassis: 250 VDC
  • Input/Output: 250 VDC (Isolated Series only)
• Certification: Carries the CE mark (Standard Series only)

**except 32-12-3 - Linear, Non-Switching
+except 32-12-3- 50% @ 24 VDC Input

Convert 20-50 VDC to 12 or 24 VDC output for powering communication/ navigation equipment, on negative ground systems. (see Isolated series, below for positive ground applications.) Ideal for powering voice, data and navigation transceivers in mobile and marine applications.

• Excellent Regulation: Output voltage maintained within 1% under all line and load conditions within rating.
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Polyurethane conformal coating on PC boards and corrosion-resistant anodized aluminum case with heavy duty shock mounts assure survival in hostile environments.
• Numerous converter and load protection circuits: Current limiting*; automatic thermal shutdown; short circuit proof*; reverse polarity and overvoltage protection*.  Except 3 Amp.
• Carries the CE mark

Isolated series
Same features as Standard Series, but with the additional capability of permitting connection of negative ground gear to positive or floating ground battery systems, or vice-versa. Many models may also be used as 12 or 24 volt stabilizers for highly input voltage sensitive equipment.

Input range:10-56 VDC; positive, negative or floating ground.
Output: 12 or 24 VDC, 3 to 35 amps.

Performance Specifications - Standard & Isolated Series

• Output: 13.6 VDC (internally adjustable 12.6-14.5) or 24.5 VDC (or specify)
• Ripple: 150 mV P-P maximum
• Regulation:
  • Standard: 1% Line/Load
  • Isolated: 2% Line/Load
  • except + 3% Line/Load
• Duty Cycle Ratings*
  • Intermittent - 20 minutes max on time, 20% duty. Current limit set at approx. 105% of intermittent rating
  • Continuous - 24 hours, 100% duty
• Idle Current:
  • Standard Series: Less than 100 mA (including power "ON" light )
  • Isolated Series: approx. 50 mA
• Operating Temp: 0-50° C, Derate Linearly From 100% @ 40° C To 50% @ 50° C Thermal shutdown @ 70° C Case Temperature
• Switching Frequency:
  • Standard: 40 Khz**
  • Isolated: 70Khz
• Efficiency: 85% - Typical.+
• Isolation:
  • Output/Chassis; Input/chassis: 250 VDC
  • Input/Output: 250 VDC (Isolated Series only)
• Certification: Carries the CE mark (Standard Series only)

**except 32-12-3 - Linear, Non-Switching
+except 32-12-3- 50% @ 24 VDC Input

Convert 20-50 VDC to 12 or 24 VDC output for powering communication/ navigation equipment, on negative ground systems. (see Isolated series, below for positive ground applications.) Ideal for powering voice, data and navigation transceivers in mobile and marine applications.

• Excellent Regulation: Output voltage maintained within 1% under all line and load conditions within rating.
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Polyurethane conformal coating on PC boards and corrosion-resistant anodized aluminum case with heavy duty shock mounts assure survival in hostile environments.
• Numerous converter and load protection circuits: Current limiting*; automatic thermal shutdown; short circuit proof*; reverse polarity and overvoltage protection*.  Except 3 Amp.
• Carries the CE mark

Isolated series
Same features as Standard Series, but with the additional capability of permitting connection of negative ground gear to positive or floating ground battery systems, or vice-versa. Many models may also be used as 12 or 24 volt stabilizers for highly input voltage sensitive equipment.

Input range:10-56 VDC; positive, negative or floating ground.
Output: 12 or 24 VDC, 3 to 35 amps.

Performance Specifications - Standard & Isolated Series

• Output: 13.6 VDC (internally adjustable 12.6-14.5) or 24.5 VDC (or specify)
• Ripple: 150 mV P-P maximum
• Regulation:
  • Standard: 1% Line/Load
  • Isolated: 2% Line/Load
  • except + 3% Line/Load
• Duty Cycle Ratings*
  • Intermittent - 20 minutes max on time, 20% duty. Current limit set at approx. 105% of intermittent rating
  • Continuous - 24 hours, 100% duty
• Idle Current:
  • Standard Series: Less than 100 mA (including power "ON" light )
  • Isolated Series: approx. 50 mA
• Operating Temp: 0-50° C, Derate Linearly From 100% @ 40° C To 50% @ 50° C Thermal shutdown @ 70° C Case Temperature
• Switching Frequency:
  • Standard: 40 Khz**
  • Isolated: 70Khz
• Efficiency: 85% - Typical.+
• Isolation:
  • Output/Chassis; Input/chassis: 250 VDC
  • Input/Output: 250 VDC (Isolated Series only)
• Certification: Carries the CE mark (Standard Series only)

**except 32-12-3 - Linear, Non-Switching
+except 32-12-3- 50% @ 24 VDC Input

Convert 20-50 VDC to 12 or 24 VDC output for powering communication/ navigation equipment, on negative ground systems. (see Isolated series, below for positive ground applications.) Ideal for powering voice, data and navigation transceivers in mobile and marine applications.

• Excellent Regulation: Output voltage maintained within 1% under all line and load conditions within rating.
• Heat generated by semi-conductors is extracted and dissipated by large heat sink fins that maximize air contact for cool operation and long life of components.
• Polyurethane conformal coating on PC boards and corrosion-resistant anodized aluminum case with heavy duty shock mounts assure survival in hostile environments.
• Numerous converter and load protection circuits: Current limiting*; automatic thermal shutdown; short circuit proof*; reverse polarity and overvoltage protection*.  Except 3 Amp.
• Carries the CE mark

Isolated series
Same features as Standard Series, but with the additional capability of permitting connection of negative ground gear to positive or floating ground battery systems, or vice-versa. Many models may also be used as 12 or 24 volt stabilizers for highly input voltage sensitive equipment.

Input range:10-56 VDC; positive, negative or floating ground.
Output: 12 or 24 VDC, 3 to 35 amps.

Performance Specifications - Standard & Isolated Series

• Output: 13.6 VDC (internally adjustable 12.6-14.5) or 24.5 VDC (or specify)
• Ripple: 150 mV P-P maximum
• Regulation:
  • Standard: 1% Line/Load
  • Isolated: 2% Line/Load
  • except + 3% Line/Load
• Duty Cycle Ratings*
  • Intermittent - 20 minutes max on time, 20% duty. Current limit set at approx. 105% of intermittent rating
  • Continuous - 24 hours, 100% duty
• Idle Current:
  • Standard Series: Less than 100 mA (including power "ON" light )
  • Isolated Series: approx. 50 mA
• Operating Temp: 0-50° C, Derate Linearly From 100% @ 40° C To 50% @ 50° C Thermal shutdown @ 70° C Case Temperature
• Switching Frequency:
  • Standard: 40 Khz**
  • Isolated: 70Khz
• Efficiency: 85% - Typical.+
• Isolation:
  • Output/Chassis; Input/chassis: 250 VDC
  • Input/Output: 250 VDC (Isolated Series only)
• Certification: Carries the CE mark (Standard Series only)

**except 32-12-3 - Linear, Non-Switching
+except 32-12-3- 50% @ 24 VDC Input

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

AC Master panels

Essential control/protection whenever AC from shorepower or generators is on board. A double pole master breaker with power on indicator light protects both hot and neutral legs of the AC circuit. A reverse polarity light provides clear warning when wiring is reversed and poses a shock hazard. Single pole branch circuit breakers (Model AC-IX) and individual ?ON? indicator lights provide control and protection of various AC loads. For 115/230 VAC applications ? see ratings note. A label set of common on-board circuits is provided.

AC-IX:
30 amp master breaker , 5 branch circuit capacity 4 installed standard 1-10A, 2-15A, 1-20A, or specify. LS-I Label set included. Panel size: 5 1/4" x 7 1/2", (13.3 X 9.5 cm.,) Weight: 2 lbs., (.9 Kg.)

AC Master panels

Essential control/protection whenever AC from shorepower or generators is on board. A double pole master breaker with power on indicator light protects both hot and neutral legs of the AC circuit. A reverse polarity light provides clear warning when wiring is reversed and poses a shock hazard. Single pole branch circuit breakers (Model AC-IX) and individual ?ON? indicator lights provide control and protection of various AC loads. For 115/230 VAC applications ? see ratings note. A label set of common on-board circuits is provided.

AC-IX:
30 amp master breaker , 5 branch circuit capacity 4 installed standard 1-10A, 2-15A, 1-20A, or specify. LS-I Label set included. Panel size: 5 1/4" x 7 1/2", (13.3 X 9.5 cm.,) Weight: 2 lbs., (.9 Kg.)

Accessory Panels

These versatile panels are ideal for smaller vessels with only a limited number of electrical circuits, or for larger systems where their modular design makes for an easy and attractive expansion of existing system capacity.

Stock panels with breakers installed come standard with DC indicator lights, but may be factory modified with AC indicator lights instead. Blank versions of the panels come with all necessary hardware to install lights and breakers. All panels are provided with a circuit identification label set of 22 common on-board electrical functions (see below).

ACCY-IX:

8 breaker capacity, 5 installed standard; 2-5A, 1-10A, 1-15A, 1-20A or specify. 8 DC circuit "ON" indicator lights installed standard, AC lights optional. Size: 7 1/2" x 5 1/4", Weight: 2 lbs.

ACCY-IBX: Blank version of ACCY-IX above. No breakers provided. Label set, light and breaker mounting hardware provided. Weight: 1 lb. 

 

Half-height version of ACCY-IX at left. 3 breaker capacity, 3 installed standard; 3 DC ?ON? indicator lights installed standard - AC optional. 1-5A, 1-10A 1-15A or specify. Size: 3 3/4" x 5 1/4", Weight: 1 lb.

ACCY-IIBX:

Installation Cut-Out Dimensions*

Accessory Panels

These versatile panels are ideal for smaller vessels with only a limited number of electrical circuits, or for larger systems where their modular design makes for an easy and attractive expansion of existing system capacity.

Stock panels with breakers installed come standard with DC indicator lights, but may be factory modified with AC indicator lights instead. Blank versions of the panels come with all necessary hardware to install lights and breakers. All panels are provided with a circuit identification label set of 22 common on-board electrical functions (see below).

ACCY-IX:

8 breaker capacity, 5 installed standard; 2-5A, 1-10A, 1-15A, 1-20A or specify. 8 DC circuit "ON" indicator lights installed standard, AC lights optional. Size: 7 1/2" x 5 1/4", Weight: 2 lbs.

ACCY-IBX: Blank version of ACCY-IX above. No breakers provided. Label set, light and breaker mounting hardware provided. Weight: 1 lb. 

 

Half-height version of ACCY-IX at left. 3 breaker capacity, 3 installed standard; 3 DC ?ON? indicator lights installed standard - AC optional. 1-5A, 1-10A 1-15A or specify. Size: 3 3/4" x 5 1/4", Weight: 1 lb.

ACCY-IIBX:

Installation Cut-Out Dimensions*

Accessory Panels

These versatile panels are ideal for smaller vessels with only a limited number of electrical circuits, or for larger systems where their modular design makes for an easy and attractive expansion of existing system capacity.

Stock panels with breakers installed come standard with DC indicator lights, but may be factory modified with AC indicator lights instead. Blank versions of the panels come with all necessary hardware to install lights and breakers. All panels are provided with a circuit identification label set of 22 common on-board electrical functions (see below).

ACCY-IX:

8 breaker capacity, 5 installed standard; 2-5A, 1-10A, 1-15A, 1-20A or specify. 8 DC circuit "ON" indicator lights installed standard, AC lights optional. Size: 7 1/2" x 5 1/4", Weight: 2 lbs.

ACCY-IBX: Blank version of ACCY-IX above. No breakers provided. Label set, light and breaker mounting hardware provided. Weight: 1 lb. 

 

Half-height version of ACCY-IX at left. 3 breaker capacity, 3 installed standard; 3 DC ?ON? indicator lights installed standard - AC optional. 1-5A, 1-10A 1-15A or specify. Size: 3 3/4" x 5 1/4", Weight: 1 lb.

ACCY-IIBX:

Installation Cut-Out Dimensions*

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

An Ac source selector switch is an essential item for any boat with an on-board AC generator and/or inverter. The switch eliminates the safety hazard and/or damage that can occur if two AC sources are applied to the same circuit simultaneously.

These switches are fitted with a compact escutcheon plate with engraved switch position nomenclature (mounting dimensions below).

The switches carry UL, CSA and VDE approval and feature heavy duty contacts and a positive step cam mechanism for low resistance contact closure. May be installed in panel with thickness up to 1/4".

An Ac source selector switch is an essential item for any boat with an on-board AC generator and/or inverter. The switch eliminates the safety hazard and/or damage that can occur if two AC sources are applied to the same circuit simultaneously.

These switches are fitted with a compact escutcheon plate with engraved switch position nomenclature (mounting dimensions below).

The switches carry UL, CSA and VDE approval and feature heavy duty contacts and a positive step cam mechanism for low resistance contact closure. May be installed in panel with thickness up to 1/4".

An Ac source selector switch is an essential item for any boat with an on-board AC generator and/or inverter. The switch eliminates the safety hazard and/or damage that can occur if two AC sources are applied to the same circuit simultaneously.

These switches are fitted with a compact escutcheon plate with engraved switch position nomenclature (mounting dimensions below).

The switches carry UL, CSA and VDE approval and feature heavy duty contacts and a positive step cam mechanism for low resistance contact closure. May be installed in panel with thickness up to 1/4".

An Ac source selector switch is an essential item for any boat with an on-board AC generator and/or inverter. The switch eliminates the safety hazard and/or damage that can occur if two AC sources are applied to the same circuit simultaneously.

These switches are fitted with a compact escutcheon plate with engraved switch position nomenclature (mounting dimensions below).

The switches carry UL, CSA and VDE approval and feature heavy duty contacts and a positive step cam mechanism for low resistance contact closure. May be installed in panel with thickness up to 1/4".

Galvanic Isolator

Sacrificial zincs corrode away as they protect metal thru hulls, shafts and props from damaging electrolysis. Stray, low voltage current flowing between the AC safety ground and DC bonding system is a principal cause of this "galvanic" action.

Installing the Galvanic Isolator between the AC safety ground and DC bonding system, blocks a majority of the low voltage currents and corrosive action on the zincs is significantly reduced (while the integrity of the critical safety ground path is maintained.) This means a significant savings in boat haul-out fees and zinc replacement costs.

For additional safety, both units feature a large capacitor, providing a secondary low impedance path for sending AC current to ground.

Use of multiple battery banks dictates that the batteries be connected or "integrated" only whenever a charge voltage is present so that they may be charged simultaneously, then disconnected or "isolated" when in use to allow for selective discharge and avoid having the secondary or standby battery drain into the primary battery.
The new Battery Integrator performs this function automatically, acting as a "smart" switch to connect independent battery banks only when a charging voltage is present. Otherwise, they are isolated, and discharge between banks is prevented.

The traditional rugged and reliable diode isolator can also be used for this function, as it also maintains isolation between banks and allows charging from multiple sources. However, one drawback is inefficiency when voltage is lost as current passes through the diodes, resulting in undercharge if the charging source does not compensate for the voltage drop.

The Battery Integrator remedies this by use of an extremely low resistance contactor which causes no voltage drop in the charging system, while the multiple batteries are charged as a single bank whenever a charging source of approximately 13.2 VDC or 26.4 VDC or greater is present (depending on model).

When the alternator or charger is off or a large load causes the voltage to drop below the disconnect point the unit breaks the common tie between the banks. This allows selective battery discharge and prevents "dumping" of a higher-charged bank into a lower-charged bank.

The unit may also be activated through the key starter or a manual switch to provide an added "boost" from the secondary battery whenever the starter is engaged and the unit senses there is sufficient voltage in that battery to provide an assist.

For systems with more than two banks, an additional unit may be installed for each additional bank to provide the same isolation and integration as described above.

The Battery Integrator is ideal for multiplying the single charging output of an inverter-charger to maintain both the house bank and an engine start bank, then to isolate them during inverter function, so current is drawn from the house bank only.

Features

• Enables charging of two separate banks without voltage drop, yet maintains 100% isolation at all other times. For systems of three banks or more, an additional unit may be installed for each additional bank
• Heavy duty silver-plated contactor, continuous duty rated to 100 amps
• Voltage sense circuit, epoxy encapsulated and heavy duty continuous rated solenoid are all designed for use in marine environments
• Easy-to-install: compact size - may be mounted with any orientation
• Easy three-wire hook up for two bank systems (BATT +, BATT +, GROUND)
• Terminal for optional wiring of remote light indicating when battery banks are integrated
• Optional internal connection can be wired though key starter or manual over ride switch, tying battery banks together for extra boost during engine start

Galvanic Isolator

Sacrificial zincs corrode away as they protect metal thru hulls, shafts and props from damaging electrolysis. Stray, low voltage current flowing between the AC safety ground and DC bonding system is a principal cause of this "galvanic" action.

Installing the Galvanic Isolator between the AC safety ground and DC bonding system, blocks a majority of the low voltage currents and corrosive action on the zincs is significantly reduced (while the integrity of the critical safety ground path is maintained.) This means a significant savings in boat haul-out fees and zinc replacement costs.

For additional safety, both units feature a large capacitor, providing a secondary low impedance path for sending AC current to ground.

Use of multiple battery banks dictates that the batteries be connected or "integrated" only whenever a charge voltage is present so that they may be charged simultaneously, then disconnected or "isolated" when in use to allow for selective discharge and avoid having the secondary or standby battery drain into the primary battery.
The new Battery Integrator performs this function automatically, acting as a "smart" switch to connect independent battery banks only when a charging voltage is present. Otherwise, they are isolated, and discharge between banks is prevented.

The traditional rugged and reliable diode isolator can also be used for this function, as it also maintains isolation between banks and allows charging from multiple sources. However, one drawback is inefficiency when voltage is lost as current passes through the diodes, resulting in undercharge if the charging source does not compensate for the voltage drop.

The Battery Integrator remedies this by use of an extremely low resistance contactor which causes no voltage drop in the charging system, while the multiple batteries are charged as a single bank whenever a charging source of approximately 13.2 VDC or 26.4 VDC or greater is present (depending on model).

When the alternator or charger is off or a large load causes the voltage to drop below the disconnect point the unit breaks the common tie between the banks. This allows selective battery discharge and prevents "dumping" of a higher-charged bank into a lower-charged bank.

The unit may also be activated through the key starter or a manual switch to provide an added "boost" from the secondary battery whenever the starter is engaged and the unit senses there is sufficient voltage in that battery to provide an assist.

For systems with more than two banks, an additional unit may be installed for each additional bank to provide the same isolation and integration as described above.

The Battery Integrator is ideal for multiplying the single charging output of an inverter-charger to maintain both the house bank and an engine start bank, then to isolate them during inverter function, so current is drawn from the house bank only.

Features

• Enables charging of two separate banks without voltage drop, yet maintains 100% isolation at all other times. For systems of three banks or more, an additional unit may be installed for each additional bank
• Heavy duty silver-plated contactor, continuous duty rated to 100 amps
• Voltage sense circuit, epoxy encapsulated and heavy duty continuous rated solenoid are all designed for use in marine environments
• Easy-to-install: compact size - may be mounted with any orientation
• Easy three-wire hook up for two bank systems (BATT +, BATT +, GROUND)
• Terminal for optional wiring of remote light indicating when battery banks are integrated
• Optional internal connection can be wired though key starter or manual over ride switch, tying battery banks together for extra boost during engine start

These heavy duty isolators allow charging multiple batteries automatically from one or two alternators, and prevent discharge or ’dumping" of one battery into another. Each battery is charged according to its need without overcharging. rated for 12-48 volt negative ground DC systems. feature conservatively rated diodes and a rustproof anodized aluminum heat sink case. Models are available for 70, 120 and 165 amp alternators.

Features:

• Heavy duty construction
• Rated for systems up to 48 volts DC, negative ground
• Rust-proof anodized aluminum case
• Stainless steel mounting hardware provided
• Protective covers provided for terminals

Performance Specifications

• Operating temperature: -40° to +80° C
• Duty cycle: Continuous rating to 50° C Derate linearly to 70% @ 80° C
• Temp. rise: 5° C at full rated current (mount vertically for optimum cooling)
• Voltage drop: 0.7V @ 50% load, 0.9V @ full load

Note: These battery isolators are not compatible with self exciting alternators. Please consult the manufacturer of your alternator if you are unsure of your configuration.

These heavy duty isolators allow charging multiple batteries automatically from one or two alternators, and prevent discharge or ’dumping" of one battery into another. Each battery is charged according to its need without overcharging. rated for 12-48 volt negative ground DC systems. feature conservatively rated diodes and a rustproof anodized aluminum heat sink case. Models are available for 70, 120 and 165 amp alternators.

Features:

• Heavy duty construction
• Rated for systems up to 48 volts DC, negative ground
• Rust-proof anodized aluminum case
• Stainless steel mounting hardware provided
• Protective covers provided for terminals

Performance Specifications

• Operating temperature: -40° to +80° C
• Duty cycle: Continuous rating to 50° C Derate linearly to 70% @ 80° C
• Temp. rise: 5° C at full rated current (mount vertically for optimum cooling)
• Voltage drop: 0.7V @ 50% load, 0.9V @ full load

Note: These battery isolators are not compatible with self exciting alternators. Please consult the manufacturer of your alternator if you are unsure of your configuration.

These heavy duty isolators allow charging multiple batteries automatically from one or two alternators, and prevent discharge or ’dumping" of one battery into another. Each battery is charged according to its need without overcharging. rated for 12-48 volt negative ground DC systems. feature conservatively rated diodes and a rustproof anodized aluminum heat sink case. Models are available for 70, 120 and 165 amp alternators.

Features:

• Heavy duty construction
• Rated for systems up to 48 volts DC, negative ground
• Rust-proof anodized aluminum case
• Stainless steel mounting hardware provided
• Protective covers provided for terminals

Performance Specifications

• Operating temperature: -40° to +80° C
• Duty cycle: Continuous rating to 50° C Derate linearly to 70% @ 80° C
• Temp. rise: 5° C at full rated current (mount vertically for optimum cooling)
• Voltage drop: 0.7V @ 50% load, 0.9V @ full load

Note: These battery isolators are not compatible with self exciting alternators. Please consult the manufacturer of your alternator if you are unsure of your configuration.

These heavy duty isolators allow charging multiple batteries automatically from one or two alternators, and prevent discharge or ’dumping" of one battery into another. Each battery is charged according to its need without overcharging. rated for 12-48 volt negative ground DC systems. feature conservatively rated diodes and a rustproof anodized aluminum heat sink case. Models are available for 70, 120 and 165 amp alternators.

Features:

• Heavy duty construction
• Rated for systems up to 48 volts DC, negative ground
• Rust-proof anodized aluminum case
• Stainless steel mounting hardware provided
• Protective covers provided for terminals

Performance Specifications

• Operating temperature: -40° to +80° C
• Duty cycle: Continuous rating to 50° C Derate linearly to 70% @ 80° C
• Temp. rise: 5° C at full rated current (mount vertically for optimum cooling)
• Voltage drop: 0.7V @ 50% load, 0.9V @ full load

Note: These battery isolators are not compatible with self exciting alternators. Please consult the manufacturer of your alternator if you are unsure of your configuration.

Reliability

Redundant, independent, charger modules increase reliability-a malfunction of one does not disable the charging system; remaining modules continue to operate.

Serviceability

• Module change-out takes only minutes, while the system continues to operate
• Technical personnel not required
• No need to remove the charger case from the boat or disconnect any wiring
• No inconvenience of power interruption to the boat

Features

• Three stage "smart" charging; bulk, absorption , float
• Battery type selector switch; gel-cell, lead-acid, AGM
• Temperature compensated output option
• Numerous diagnostic and system status indicators
• 12 Volt; 40-120 amps or 24 Volt; 22-67 amps
• "Universal" input of 90-264 VAC, 50-60 Hz.-can be used anywhere in the world
• Powder coated stainless steel case

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Phase Three "Smart" battery charging technology is now available in a wide range of power levels, allowing you to select the right size, features and flexibility you require for virtually any appliocation from small recreational craft to large live-aboards, workboats and other commercial vessels. These chargers interact with batteries to put them through the optimum three stage charge process which provides for fastest recovery and ideal conditioning, maximizing battery performance and extending battery life.

A selector switch adjusts output voltage to adapt for gel-cell/flooded lead-acid/AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. All models are housed in a rugged stainless steel case, and the internal circuitry is polyurethane coated for maximum corrosion resistance.

Features

• "Smart" circuitry provides three stage charging-bulk, absorption, float.
• Wide model range covers battery system ratings from 14-950 amp-hours
• Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages.
• Multiple isolated output banks; ammeter indicates total output current*.
• Optional sensor adjusts output voltage based on battery temperature*. *except PT-7.
• Current limiting-prevents damage from overloading.
• Charger status clearly displayed with L.E.D. and/or audible indicators or optional remote panel.
• Use as a power supply; can power loads without a battery in line.
• Built to last-rugged stainless steel case with drip shield and marinized internal circuitry.
• Numerous Safety and EMC Compliances
• Full two year parts and labor warranty

Displays volts, amps, energy used and remaining for 12 or 24 volt systems up to 500 amps and up to 3,000 amp-hour capacity. Makes DC energy management a breeze. Monitor voltage on up to three separate banks. House bank (or battery bank of choice) may be also be programmed for the following functions: 1) Monitor charge/discharge amperage. 2) Total energy monitor can be set for amp-hours or percent-of-charge. 3) High/low voltage alarm, plus alarm set-point for low amp-hours remaining. 500 amp shunt included. NMEA 0183 compatible output for data logging. 2 1/2" square face

For 115/230 volt systems. Reads: 90-300 VAC, 0-150 amps, frequency from 40-70 Hz and power from 0-45 kW. Features alarm circuits for high/low voltage and high/low frequency. Can be programmed to provide automatic generator shutdown (see Remote Alarm Option below) in the event that voltage or frequency exceed predetermined range. Current and voltage transformers are included. 12 or 24 volt source required to power meter.  2 1/2 " face

The ABC Series chargers have been in the Newmar line for 30 years. They utilize time tested SCR charging circuitry, individually sensing and regulating each of 2 isolated battery banks, allowing the user to leave the charger operating indefinitely, even under no-load conditions without fear of overcharging. These chargers are ideal for vessels or vehicles which have an intermittent demand for battery power.

These chargers are housed in a rugged, black anodized aluminum, heat-sink case which extracts heat without introducing dust and moisture to the inside of the unit.

The rugged and reliable ABC charger is employed in hostile environments throughout the world in recreation and commercial marine applications, off-shore oil platforms, in mining equipment, emergency service vehicles and rugged off-road applications.

They feature a total output ammeter, on-off power switch, power "on" indicator light, 115/230 VAC input voltage selector switch, factory installed AC power cord with molded plug and shock-resistant rubber mounting grommets. Circuit boards are polyurethane conformal coated for corrosion resistance and all are protected against overheating by an automatically resetting thermal switch.

Features

• Total output ammeter
• Dual independently regulated output banks
• On-off switch and power ?on? indicator light
• Vibration absorbing mounting grommets
• Anodized aluminum case
• 115/230 VAC input selector switch
• Auto-reset thermal breaker
• Conformal coating of circuit board

Specifications

• Duty Cycle Ratings: Rated Charging Output 20 min., derate to 50% for continuous output
• Operating Temperature: 0-40°C
• Float Voltage: 13.4 VDC

The ABC Series chargers have been in the Newmar line for 30 years. They utilize time tested SCR charging circuitry, individually sensing and regulating each of 2 isolated battery banks, allowing the user to leave the charger operating indefinitely, even under no-load conditions without fear of overcharging. These chargers are ideal for vessels or vehicles which have an intermittent demand for battery power.

These chargers are housed in a rugged, black anodized aluminum, heat-sink case which extracts heat without introducing dust and moisture to the inside of the unit.

The rugged and reliable ABC charger is employed in hostile environments throughout the world in recreation and commercial marine applications, off-shore oil platforms, in mining equipment, emergency service vehicles and rugged off-road applications.

They feature a total output ammeter, on-off power switch, power "on" indicator light, 115/230 VAC input voltage selector switch, factory installed AC power cord with molded plug and shock-resistant rubber mounting grommets. Circuit boards are polyurethane conformal coated for corrosion resistance and all are protected against overheating by an automatically resetting thermal switch.

Features

• Total output ammeter
• Dual independently regulated output banks
• On-off switch and power ?on? indicator light
• Vibration absorbing mounting grommets
• Anodized aluminum case
• 115/230 VAC input selector switch
• Auto-reset thermal breaker
• Conformal coating of circuit board

Specifications

• Duty Cycle Ratings: Rated Charging Output 20 min., derate to 50% for continuous output
• Operating Temperature: 0-40°C
• Float Voltage: 13.4 VDC

AQ Series Waterproof Radio Covers
Hand-held radios can be taken anywhere without being damaged by water, dust or sand when the AQ Series waterproof cover is used for protection. Even total immersion will not harm the radio. These covers are certified waterproof to a depth of 33 feet.

The case is made of super-tough, UV resistant PVC, which is engineered with enough flexibility to facilitate easy operation of knobs and keypads. Transparent design allows easy reading of digital displays. Sound is virtually unimpeded and RF transmission is unaffected.

A quick release clip allows easy insertion and removal of the radio and a handy lanyard provides extra security when hands are wet. But if the radio falls into deep water, no problem! Safely inside the AQ case, it will float!

Models
AQ-20L/R For standard size hand-helds. New reversible design accommodates both left and right hand antennas
AQ-2MXL Larger and longer than AQ-20 for high power radios with large battery packs
 

The Phone-Com intercom system provides direct, wired, point-to-point communication anywhere on the vessel. Voice contact to any phone in the system is as easy as lifting the receiver and pressing the call button. Phone-Com operates on 12 VDC. They are constructed of high-impact plastic and are available in either bright white or traditional black. Bulkhead mounting bracket is provided. Two versions are available:

PI-2: Designed for communication between only two points. A single call button sounds a buzzer and illuminates an indicator lamp on the companion phone. Available singly or as a set with 40’ of interconnect wire, fuse, terminal lugs and mounting hardware.

PI-2 SET: Two station phone set, 40’ interconnect wire, fuse, lugs, mounting hardware; 5 lbs.

PI-10:For multiple station calling capability. Up to 10 phones may be interconnected, and each phone has 10 call buttons. Sold individually-- see wiring requirements below.

Phone-Com Wiring: For PI-2, use 5 conductor wire. For PI-10, add 3 to the total number of stations to determine minimum number of conductors required.

Note: Phones are not waterproof and should be installed in a protected location

The Phone-Com intercom system provides direct, wired, point-to-point communication anywhere on the vessel. Voice contact to any phone in the system is as easy as lifting the receiver and pressing the call button. Phone-Com operates on 12 VDC. They are constructed of high-impact plastic and are available in either bright white or traditional black. Bulkhead mounting bracket is provided. Two versions are available:

PI-2: Designed for communication between only two points. A single call button sounds a buzzer and illuminates an indicator lamp on the companion phone. Available singly or as a set with 40’ of interconnect wire, fuse, terminal lugs and mounting hardware.

PI-2 SET: Two station phone set, 40’ interconnect wire, fuse, lugs, mounting hardware; 5 lbs.

PI-10:For multiple station calling capability. Up to 10 phones may be interconnected, and each phone has 10 call buttons. Sold individually-- see wiring requirements below.

Phone-Com Wiring: For PI-2, use 5 conductor wire. For PI-10, add 3 to the total number of stations to determine minimum number of conductors required.

Note: Phones are not waterproof and should be installed in a protected location

The Phone-Com intercom system provides direct, wired, point-to-point communication anywhere on the vessel. Voice contact to any phone in the system is as easy as lifting the receiver and pressing the call button. Phone-Com operates on 12 VDC. They are constructed of high-impact plastic and are available in either bright white or traditional black. Bulkhead mounting bracket is provided. Two versions are available:

PI-2: Designed for communication between only two points. A single call button sounds a buzzer and illuminates an indicator lamp on the companion phone. Available singly or as a set with 40’ of interconnect wire, fuse, terminal lugs and mounting hardware.

PI-2 SET: Two station phone set, 40’ interconnect wire, fuse, lugs, mounting hardware; 5 lbs.

PI-10:For multiple station calling capability. Up to 10 phones may be interconnected, and each phone has 10 call buttons. Sold individually-- see wiring requirements below.

Phone-Com Wiring: For PI-2, use 5 conductor wire. For PI-10, add 3 to the total number of stations to determine minimum number of conductors required.

Note: Phones are not waterproof and should be installed in a protected location

The Phone-Com intercom system provides direct, wired, point-to-point communication anywhere on the vessel. Voice contact to any phone in the system is as easy as lifting the receiver and pressing the call button. Phone-Com operates on 12 VDC. They are constructed of high-impact plastic and are available in either bright white or traditional black. Bulkhead mounting bracket is provided. Two versions are available:

PI-2: Designed for communication between only two points. A single call button sounds a buzzer and illuminates an indicator lamp on the companion phone. Available singly or as a set with 40’ of interconnect wire, fuse, terminal lugs and mounting hardware.

PI-2 SET: Two station phone set, 40’ interconnect wire, fuse, lugs, mounting hardware; 5 lbs.

PI-10:For multiple station calling capability. Up to 10 phones may be interconnected, and each phone has 10 call buttons. Sold individually-- see wiring requirements below.

Phone-Com Wiring: For PI-2, use 5 conductor wire. For PI-10, add 3 to the total number of stations to determine minimum number of conductors required.

Note: Phones are not waterproof and should be installed in a protected location

The Phone-Com intercom system provides direct, wired, point-to-point communication anywhere on the vessel. Voice contact to any phone in the system is as easy as lifting the receiver and pressing the call button. Phone-Com operates on 12 VDC. They are constructed of high-impact plastic and are available in either bright white or traditional black. Bulkhead mounting bracket is provided. Two versions are available:

PI-2: Designed for communication between only two points. A single call button sounds a buzzer and illuminates an indicator lamp on the companion phone. Available singly or as a set with 40’ of interconnect wire, fuse, terminal lugs and mounting hardware.

PI-2 SET: Two station phone set, 40’ interconnect wire, fuse, lugs, mounting hardware; 5 lbs.

PI-10:For multiple station calling capability. Up to 10 phones may be interconnected, and each phone has 10 call buttons. Sold individually-- see wiring requirements below.

Phone-Com Wiring: For PI-2, use 5 conductor wire. For PI-10, add 3 to the total number of stations to determine minimum number of conductors required.

Note: Phones are not waterproof and should be installed in a protected location

The Phone-Com intercom system provides direct, wired, point-to-point communication anywhere on the vessel. Voice contact to any phone in the system is as easy as lifting the receiver and pressing the call button. Phone-Com operates on 12 VDC. They are constructed of high-impact plastic and are available in either bright white or traditional black. Bulkhead mounting bracket is provided. Two versions are available:

PI-2: Designed for communication between only two points. A single call button sounds a buzzer and illuminates an indicator lamp on the companion phone. Available singly or as a set with 40’ of interconnect wire, fuse, terminal lugs and mounting hardware.

PI-2 SET: Two station phone set, 40’ interconnect wire, fuse, lugs, mounting hardware; 5 lbs.

PI-10:For multiple station calling capability. Up to 10 phones may be interconnected, and each phone has 10 call buttons. Sold individually-- see wiring requirements below.

Phone-Com Wiring: For PI-2, use 5 conductor wire. For PI-10, add 3 to the total number of stations to determine minimum number of conductors required.

Note: Phones are not waterproof and should be installed in a protected location

The new Digital Battery Analyzer (model DBA) is an essential tool for all DC system installers, technicians and battery dealers . Simple to use, it performs a complete analysis of battery condition in mere seconds, then displays conclusive data on a large clear LCD readout.

The DBA analyzes 12 and 6 volt lead-acid batteries of all types with ratings from 100-1400 CCA. It provides information on battery voltage, battery condition and available battery power. This gives you empirical data to assure your customers that their batteries are fine, or to support your recommendation that they be replaced.

As long as no load is applied, it is not necessary to disconnect the batteries to perform the test. When analyzing 24 or 48 volt battery systems, there is no need to disconnect the 12 volt batteries within the string to test them individually. Automatic state-of-charge compensation enables accurate analysis of batteries, even when they are discharged as low as 5.5 volts, avoiding time-consuming recharge prior to testing.

The DBA utilizes a sophisticated test algorithm that measures battery cell conductance, which is affected by sulfation or loss of active material. This test has proven to be an accurate indicator of cranking ability, standby energy capacity and general state of health, regardless of state of charge. The test produces no heat, is completely harmless to the battery cells and causes no significant discharge.

The unit is housed in rugged ABS plastic, yet is light-weight and compact for use in cramped battery compartments and portability in tool kits. It comes equipped with 32" polarity color-coded test leads and quick-connect clamps. The DBA even indicates whether the clamps have proper contact with battery posts.

No internal battery nor external AC power source is required. Clear and concise operating instructions are provided.


Features:

• Analyzes 12 volt and 6 volt lead-acid batteries of all types: flooded, gel-cell or AGM; deep-cycle or gen/engine start
• Simple three step test procedure provides a comprehensive analysis of batteries in seconds.
• No need to recharge batteries prior to testing ; accurate results for batteries in any state of charge down to 5.5 volts
• Uses sophisticated conductance technology; will not harm or discharge batteries
• Rugged, compact, light-weight case; easy to use even in hard-to-access battery compartments
• Temperature compensation setting when testing batteries below 32øF (0øC)

All circuit breakers offered by NEWMAR are UL recognized and CSA listed for AC and DC
systems and meet USCG requirements as a qualified circuit protection device.

Single and Double Pole

Fit all NEWMAR electrical panels, as well as most other brands

• Feature magnetic-hydraulic "trip-free" mechanism
• 5-30 amp rated to 65 VDC or 277 VAC; 40, 50 amp rated to 32 VDC or 120 VAC (See rating note below).
• Mounting scrws not provide order separatly
• #10 screw terminals on rear for wiring

Options

• Red, white or black toggle handles
• Single pole values: 5, 10, 15, 20, 25, 30, 40 or 50 amp.
• Double pole values: 15, 20, 30 or 50 amp

Important Circuit Breaker Rating Note: Standard series breakers shown on this page which are rated higher than 30 amps are acceptable for use in 230 VAC Line-to-Line systems (where each leg is 115 VAC - to - neutral), but are not rated for 230 VAC line-to-neutral systems.

Features:

• Industrial grade panel, components and heavy duty vibration mounts designed for emergency vehicle use
• Numerous size panels match available roof space (1.2 to 7+ Amps); panels can be wired for higher output
• Voltage controller adapts to properly charging different battery types
• Kits contain all parts needed for various types of vehicle installations

Benefits:

• Keep up with radio load without running engine or plugging in
• Helps comply with anti idle laws
• Saves fuel cost and engine maintenance
• Eliminate the need to jump start reserve vehicles
• Ideal for vehicles with mobile computers and radio?s

Complete Heavy Duty Kits Kit Includes:

Complete instructions and parts provided, assures professional installation, eliminates installer guess work and parts sourcing

• Industrial grade solar panel with 10 year warranty
• Charge controller with temperature compensated, three-step output and battery type selection (Flooded/AGM)
• Heavy duty vibration dampened mounting system
• 20 foot duplex wire, terminals and cable ties
• Waterproof wire feed-through fitting included
• All mounting hardware included for various truck installations

Features:

• Industrial grade panel, components and heavy duty vibration mounts designed for emergency vehicle use
• Numerous size panels match available roof space (1.2 to 7+ Amps); panels can be wired for higher output
• Voltage controller adapts to properly charging different battery types
• Kits contain all parts needed for various types of vehicle installations

Benefits:

• Keep up with radio load without running engine or plugging in
• Helps comply with anti idle laws
• Saves fuel cost and engine maintenance
• Eliminate the need to jump start reserve vehicles
• Ideal for vehicles with mobile computers and radio?s

Complete Heavy Duty Kits Kit Includes:

Complete instructions and parts provided, assures professional installation, eliminates installer guess work and parts sourcing

• Industrial grade solar panel with 10 year warranty
• Charge controller with temperature compensated, three-step output and battery type selection (Flooded/AGM)
• Heavy duty vibration dampened mounting system
• 20 foot duplex wire, terminals and cable ties
• Waterproof wire feed-through fitting included
• All mounting hardware included for various truck installations

Features:

• Industrial grade panel, components and heavy duty vibration mounts designed for emergency vehicle use
• Numerous size panels match available roof space (1.2 to 7+ Amps); panels can be wired for higher output
• Voltage controller adapts to properly charging different battery types
• Kits contain all parts needed for various types of vehicle installations

Benefits:

• Keep up with radio load without running engine or plugging in
• Helps comply with anti idle laws
• Saves fuel cost and engine maintenance
• Eliminate the need to jump start reserve vehicles
• Ideal for vehicles with mobile computers and radio?s

Complete Heavy Duty Kits Kit Includes:

Complete instructions and parts provided, assures professional installation, eliminates installer guess work and parts sourcing

• Industrial grade solar panel with 10 year warranty
• Charge controller with temperature compensated, three-step output and battery type selection (Flooded/AGM)
• Heavy duty vibration dampened mounting system
• 20 foot duplex wire, terminals and cable ties
• Waterproof wire feed-through fitting included
• All mounting hardware included for various truck installations

Features:

• Industrial grade panel, components and heavy duty vibration mounts designed for emergency vehicle use
• Numerous size panels match available roof space (1.2 to 7+ Amps); panels can be wired for higher output
• Voltage controller adapts to properly charging different battery types
• Kits contain all parts needed for various types of vehicle installations

Benefits:

• Keep up with radio load without running engine or plugging in
• Helps comply with anti idle laws
• Saves fuel cost and engine maintenance
• Eliminate the need to jump start reserve vehicles
• Ideal for vehicles with mobile computers and radio?s

Complete Heavy Duty Kits Kit Includes:

Complete instructions and parts provided, assures professional installation, eliminates installer guess work and parts sourcing

• Industrial grade solar panel with 10 year warranty
• Charge controller with temperature compensated, three-step output and battery type selection (Flooded/AGM)
• Heavy duty vibration dampened mounting system
• 20 foot duplex wire, terminals and cable ties
• Waterproof wire feed-through fitting included
• All mounting hardware included for various truck installations

Features:

• Industrial grade panel, components and heavy duty vibration mounts designed for emergency vehicle use
• Numerous size panels match available roof space (1.2 to 7+ Amps); panels can be wired for higher output
• Voltage controller adapts to properly charging different battery types
• Kits contain all parts needed for various types of vehicle installations

Benefits:

• Keep up with radio load without running engine or plugging in
• Helps comply with anti idle laws
• Saves fuel cost and engine maintenance
• Eliminate the need to jump start reserve vehicles
• Ideal for vehicles with mobile computers and radio?s

Complete Heavy Duty Kits Kit Includes:

Complete instructions and parts provided, assures professional installation, eliminates installer guess work and parts sourcing

• Industrial grade solar panel with 10 year warranty
• Charge controller with temperature compensated, three-step output and battery type selection (Flooded/AGM)
• Heavy duty vibration dampened mounting system
• 20 foot duplex wire, terminals and cable ties
• Waterproof wire feed-through fitting included
• All mounting hardware included for various truck installations

Features:

• Industrial grade panel, components and heavy duty vibration mounts designed for emergency vehicle use
• Numerous size panels match available roof space (1.2 to 7+ Amps); panels can be wired for higher output
• Voltage controller adapts to properly charging different battery types
• Kits contain all parts needed for various types of vehicle installations

Benefits:

• Keep up with radio load without running engine or plugging in
• Helps comply with anti idle laws
• Saves fuel cost and engine maintenance
• Eliminate the need to jump start reserve vehicles
• Ideal for vehicles with mobile computers and radio?s

Complete Heavy Duty Kits Kit Includes:

Complete instructions and parts provided, assures professional installation, eliminates installer guess work and parts sourcing

• Industrial grade solar panel with 10 year warranty
• Charge controller with temperature compensated, three-step output and battery type selection (Flooded/AGM)
• Heavy duty vibration dampened mounting system
• 20 foot duplex wire, terminals and cable ties
• Waterproof wire feed-through fitting included
• All mounting hardware included for various truck installations

Features:

• Industrial grade panel, components and heavy duty vibration mounts designed for emergency vehicle use
• Numerous size panels match available roof space (1.2 to 7+ Amps); panels can be wired for higher output
• Voltage controller adapts to properly charging different battery types
• Kits contain all parts needed for various types of vehicle installations

Benefits:

• Keep up with radio load without running engine or plugging in
• Helps comply with anti idle laws
• Saves fuel cost and engine maintenance
• Eliminate the need to jump start reserve vehicles
• Ideal for vehicles with mobile computers and radio?s

Complete Heavy Duty Kits Kit Includes:

Complete instructions and parts provided, assures professional installation, eliminates installer guess work and parts sourcing

• Industrial grade solar panel with 10 year warranty
• Charge controller with temperature compensated, three-step output and battery type selection (Flooded/AGM)
• Heavy duty vibration dampened mounting system
• 20 foot duplex wire, terminals and cable ties
• Waterproof wire feed-through fitting included
• All mounting hardware included for various truck installations

Features:

• Industrial grade panel, components and heavy duty vibration mounts designed for emergency vehicle use
• Numerous size panels match available roof space (1.2 to 7+ Amps); panels can be wired for higher output
• Voltage controller adapts to properly charging different battery types
• Kits contain all parts needed for various types of vehicle installations

Benefits:

• Keep up with radio load without running engine or plugging in
• Helps comply with anti idle laws
• Saves fuel cost and engine maintenance
• Eliminate the need to jump start reserve vehicles
• Ideal for vehicles with mobile computers and radio?s

Complete Heavy Duty Kits Kit Includes:

Complete instructions and parts provided, assures professional installation, eliminates installer guess work and parts sourcing

• Industrial grade solar panel with 10 year warranty
• Charge controller with temperature compensated, three-step output and battery type selection (Flooded/AGM)
• Heavy duty vibration dampened mounting system
• 20 foot duplex wire, terminals and cable ties
• Waterproof wire feed-through fitting included
• All mounting hardware included for various truck installations

Features:

• Industrial grade panel, components and heavy duty vibration mounts designed for emergency vehicle use
• Numerous size panels match available roof space (1.2 to 7+ Amps); panels can be wired for higher output
• Voltage controller adapts to properly charging different battery types
• Kits contain all parts needed for various types of vehicle installations

Benefits:

• Keep up with radio load without running engine or plugging in
• Helps comply with anti idle laws
• Saves fuel cost and engine maintenance
• Eliminate the need to jump start reserve vehicles
• Ideal for vehicles with mobile computers and radio?s

Complete Heavy Duty Kits Kit Includes:

Complete instructions and parts provided, assures professional installation, eliminates installer guess work and parts sourcing

• Industrial grade solar panel with 10 year warranty
• Charge controller with temperature compensated, three-step output and battery type selection (Flooded/AGM)
• Heavy duty vibration dampened mounting system
• 20 foot duplex wire, terminals and cable ties
• Waterproof wire feed-through fitting included
• All mounting hardware included for various truck installations