Amphibian A12 Pro

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A12Pro underwater light rivals any 50 watt Xenon on the market and with 8 times the power savings. The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way. Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to 50w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A12 Pro

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A12Pro underwater light rivals any 50 watt Xenon on the market and with 8 times the power savings. The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way. Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to 50w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A12 Pro

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A12Pro underwater light rivals any 50 watt Xenon on the market and with 8 times the power savings. The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way. Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to 50w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Seasucker A3 Kit

Temporarily mount your Amphibians anywhere; underwater or on deck! Take your lights with you for added security, or from boat to boat for multiple use. Suction mounts to any smooth surface. 3 SeaSucker models compatible with all Amphibians. (Amphibian Pro Series can only be mounted underwater).

• Easy to use - attaches and removes in seconds
  
• Use underwater or on deck
  
• Versatile - suction mounts to any smooth surface
  
• Powerful holding capabilities

Seasucker A6 Kit

Temporarily mount your Amphibians anywhere; underwater or on deck! Take your lights with you for added security, or from boat to boat for multiple use. Suction mounts to any smooth surface. 3 SeaSucker models compatible with all Amphibians. (Amphibian Pro Series can only be mounted underwater).

• Easy to use - attaches and removes in seconds
  
• Use underwater or on deck
  
• Versatile - suction mounts to any smooth surface
  
• Powerful holding capabilities

Seasucker A12 Kit

Temporarily mount your Amphibians anywhere; underwater or on deck! Take your lights with you for added security, or from boat to boat for multiple use. Suction mounts to any smooth surface. 3 SeaSucker models compatible with all Amphibians. (Amphibian Pro Series can only be mounted underwater).

• Easy to use - attaches and removes in seconds
  
• Use underwater or on deck
  
• Versatile - suction mounts to any smooth surface
  
• Powerful holding capabilities

Amphibian T3 Trailer Boat Series

The New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T3 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as dock lighting.

Ultra low power draw, no start-up current required.

Features

Amphibian T3 Trailer Boat Series

The New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T3 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as dock lighting.

Ultra low power draw, no start-up current required.

Features

Amphibian T3 Trailer Boat Series

The New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T3 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as dock lighting.

Ultra low power draw, no start-up current required.

Features

Amphibian T6 - Trailer Boat Series

The New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T6 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as dock lighting.

Ultra low power draw, no start-up current required.

Features

Amphibian T6 - Trailer Boat Series

The New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T6 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as dock lighting.

Ultra low power draw, no start-up current required.

Features

Amphibian T6 - Trailer Boat Series

The New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T6 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as dock lighting.

Ultra low power draw, no start-up current required.

Features

Amphibian A3 Pro - Underwater Lighting Experience

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A3Pro underwater light rivals any 75 watt Halogen on the market and with 8 times the power savings.

The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way.

Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as dock lighting.

Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

Features:

Amphibian A3 Pro - Underwater Lighting Experience

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A3Pro underwater light rivals any 75 watt Halogen on the market and with 8 times the power savings.

The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way.

Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as dock lighting.

Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

Features:

Amphibian A3 Pro - Underwater Lighting Experience

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A3Pro underwater light rivals any 75 watt Halogen on the market and with 8 times the power savings.

The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way.

Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as dock lighting.

Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

Features:

Amphibian A6 Pro - Underwater Lighting Experience

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A6Pro underwater light rivals any 35 watt Xenon on the market and with 8 times the power savings.

The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way.

Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as dock lighting.

Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

Features:

Amphibian A6 Pro - Underwater Lighting Experience

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A6Pro underwater light rivals any 35 watt Xenon on the market and with 8 times the power savings.

The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way.

Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as dock lighting.

Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

Features:

Amphibian A6 Pro - Underwater Lighting Experience

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A6Pro underwater light rivals any 35 watt Xenon on the market and with 8 times the power savings.

The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way.

Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as dock lighting.

Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

Features:

Hybrid Series 30i
The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light - either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 40% brighter than its predecessor the 1520 the 30i is equivalent to any 50w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65’), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

Features

• All-in-One Technology
  
• Versatile Mounting Options
  
• Ultra-High Light Output - equal to 50w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts
  
• Reverse Polarity Protected

Hybrid Series 30i
The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light - either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 40% brighter than its predecessor the 1520 the 30i is equivalent to any 50w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65’), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

Features

• All-in-One Technology
  
• Versatile Mounting Options
  
• Ultra-High Light Output - equal to 50w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts
  
• Reverse Polarity Protected

Hybrid Series 30i
The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light - either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 40% brighter than its predecessor the 1520 the 30i is equivalent to any 50w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65’), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

Features

• All-in-One Technology
  
• Versatile Mounting Options
  
• Ultra-High Light Output - equal to 50w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts
  
• Reverse Polarity Protected

Hybrid Series 60i
The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light - either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 20% brighter than its predecessor the 2010 the 60i is equivalent to any 100w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65’), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

Features

• All-in-One Technology
  
• Versatile Mounting Options
  
• Ultra-High Light Output - equal to 100w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts
  
• Reverse Polarity Protected

Hybrid Series 60i
The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light - either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 20% brighter than its predecessor the 2010 the 60i is equivalent to any 100w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65’), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

Features

• All-in-One Technology
  
• Versatile Mounting Options
  
• Ultra-High Light Output - equal to 100w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts
  
• Reverse Polarity Protected

Hybrid Series 60i
The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light - either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 20% brighter than its predecessor the 2010 the 60i is equivalent to any 100w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65’), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

Features

• All-in-One Technology
  
• Versatile Mounting Options
  
• Ultra-High Light Output - equal to 100w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts
  
• Reverse Polarity Protected

Pro Series 2010 Thru-Hull

The Original Thru-Hull with the world’s smallest hole cut-out for a thru hull light at only 1"! The 2010 with a ¹³⁄₁₆" (30mm) profile head and the brightness equivalent to some 50w Xenon makes it ideal for transom mount applications. Ideally suited for boats up to 65’ (20m) using 2-6 lights with spacing of 3-5’ (1-1.5m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system. Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

• 1" Hole in Hull
  
• Equal to 50w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

Pro Series 2010 Thru-Hull

The Original Thru-Hull with the world’s smallest hole cut-out for a thru hull light at only 1"! The 2010 with a ¹³⁄₁₆" (30mm) profile head and the brightness equivalent to some 50w Xenon makes it ideal for transom mount applications. Ideally suited for boats up to 65’ (20m) using 2-6 lights with spacing of 3-5’ (1-1.5m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system. Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

• 1" Hole in Hull
  
• Equal to 50w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

Pro Series 1520 Flush Mount

The Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options. This light can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output. Ideally suited for boats up to 35’ (10m) using 2-4 lights per side with spacing of 2-4’ (0.5-1.2m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system. Suitable for Fiberglass, GRP and wooden hulls, and now also avail- able for use on aluminium/steel hulls using the Delrin Sleeve option.

• 2-⅝" Hole - Easy to Retrofit
  
• Equal to some 35w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

Pro Series 3010 Thru-Hull

The Original Thru-Hull with the world’s smallest hole cut-out for a thru hull light at only 1"! The 3010 with a ¹³⁄₈" (35mm) profile head and the brightness equivalent to some 150w HID Metal Halides makes it ideal for transom mount applications. Ideally suited for boats of 65’ (20m) or above using 4 or more lights with spacing of 3-6’ (1-1.8m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system. Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

• 1" Hole in Hull
  
• Equal to 150w HID/Metal Halide
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

Pro Series 2010 Flush Mount

The Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options. This light can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output. Ideally suited for boats up to 65’ (20m) using 2-6 lights per side with spacing of 3-6’ (1-1.8m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system. Suitable for Fiberglass, GRP and wooden hulls, and now also avail- able for use on aluminium/steel hulls using the Delrin Sleeve option.

• 3-¼" Hole - Easy to Retrofit
  
• Equal to 50w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

Pro Series 3010 Flush Mount

The Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options. This light can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output. Ideally suited for boats of 65’ (20m) or above using 4 or more lights per side with spacing of 4-8’ (1.2-2.4m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system. Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

• 4-⅛" Hole - Easy to Retrofit
  
• Equal to 150w HID/Metal Halide
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

Pro Series 3010 Thru-Hull

The Original Thru-Hull with the world’s smallest hole cut-out for a thru hull light at only 1"! The 3010 with a ¹³⁄₈" (35mm) profile head and the brightness equivalent to some 150w HID Metal Halides makes it ideal for transom mount applications. Ideally suited for boats of 65’ (20m) or above using 4 or more lights with spacing of 3-6’ (1-1.8m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system. Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

• 1" Hole in Hull
  
• Equal to 150w HID/Metal Halide
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

EYES Ocean Camera

EYES Ocean Camera can be mounted anywhere allowing you to capture the magic of your own underwater aquarium beneath your boat, increase security above and below the water, and provide evidence of your winning tournament catch. Standard VGA output connects to any screen. Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option. Weld-in option also available on special request. Tritonium Optical Lens is scratch and sea growth resistant.

• (1) ⅜" Hole in Hull
  
• Standard VGA
  
• 12vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Tritonium Optical Lens
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

Pro Series 1520 Flush Mount

The Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options. This light can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output. Ideally suited for boats up to 35’ (10m) using 2-4 lights per side with spacing of 2-4’ (0.5-1.2m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system. Suitable for Fiberglass, GRP and wooden hulls, and now also avail- able for use on aluminium/steel hulls using the Delrin Sleeve option.

• 2-⅝" Hole - Easy to Retrofit
  
• Equal to some 35w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A3 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to 50w Halogen
  
• 12vDC ONLY
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A3 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to 50w Halogen
  
• 12vDC ONLY
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A3 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to 50w Halogen
  
• 12vDC ONLY
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A6 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to 80w Halogen
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A6 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to 80w Halogen
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A12 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to some 35w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A12 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to some 35w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A12 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to some 35w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Pro Series 2010 Thru-Hull - 180° Beam

The Original Thru-Hull with the world’s smallest hole cut-out for a thru hull light at only 1"! The 2010 with a ¹³⁄₁₆" (30mm) profile head and the brightness equivalent to some 50w Xenon makes it ideal for transom mount applications. Ideally suited for boats up to 65’ (20m) using 2-6 lights with spacing of 3-5’ (1-1.5m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system. Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

• 1" Hole in Hull
  
• Equal to 50w Xenon
  
• 12/24vDC
  
• 180° Beam
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

Pro Series 2010 Flush Mount - 180° Beam

The Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options. This light can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output. Ideally suited for boats up to 65’ (20m) using 2-6 lights per side with spacing of 3-6’ (1-1.8m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system. Suitable for Fiberglass, GRP and wooden hulls, and now also avail- able for use on aluminium/steel hulls using the Delrin Sleeve option.

• 3-¼" Hole - Easy to Retrofit
  
• Equal to 50w Xenon
  
• 12/24vDC
  
• 180° Beam
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

Pro Series 3010 Flush Mount - 180° Beam

The Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options. This light can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output. Ideally suited for boats of 65’ (20m) or above using 4 or more lights per side with spacing of 4-8’ (1.2-2.4m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system. Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

• 4-⅛" Hole - Easy to Retrofit
  
• Equal to 150w HID/Metal Halide
  
• 12/24vDC
  
• 180° Beam
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A3 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to 50w Halogen
  
• 12vDC ONLY
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A12 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to some 35w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A3 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to 50w Halogen
  
• 12vDC ONLY
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A6 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to 80w Halogen
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

Amphibian A12 Classic

The Amphibian Series is the world’s first lighting collection designed to be used both in and out of the water. Extremely powerful but with ultra low power draw and no start-up current required. Exceptionally easy to install and versatile enough to be mounted onto any transom, under the gunnels, engine brackets, t-tops, on masts as uplighters, and even on trailers for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series. Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• ⅜" Hole in Hull
  
• Equal to some 35w Xenon
  
• 12/24vDC
  
• 40,000+ Hour Life
  
• Chemically Resistant Polymer
  
• Twin Core Wire
  
• Factory Sealed Unit
  
• No Breakable Parts

The original Thru-Hull with the worlds smallest hole cut-out for a thru hull light at only 1"! This light with its 30mm profile head makes it suitable for Transom mount applications. A very quick to fit and effective underwater light.

All lights now utilize Tritonium Optical lenses , and are supplied with a quick connect system by Deutsch, ensuring almost ’ fool proof’ installation and compliance with ABYC, E11 regulations.

Approved by Lloyds register and undergoing UL, RINA, DNV and ABS approvals.

The original Thru-Hull with the worlds smallest hole cut-out for a thru hull light at only 1"! This light with a 30mm profile head makes it ideal for Transom mount applications. A very quick to fit and effective underwater light.

Suitable for Fiberglass, GRP and wooden hulls and now also available for use on aluminium/steel hulls using the delrin sleeve.

Lloyds Type Approved, RINA, ABS Type Approved, USCG Ignition Protected and ABYC H-27 Side Load approved.

All lights utilize Tritonium Optical lenses, and are supplied with a quick connect system by Deutsch ensuring almost ’fool proof’ installation and compliance with ABYC, E11 regulations.

The original Thru-Hull with the worlds smallest hole cut-out for a thru hull light at only 1"! This light with a 30mm profile head makes it ideal for Transom mount applications. A very quick to fit and effective underwater light.

Suitable for Fiberglass, GRP and wooden hulls and now also available for use on aluminium/steel hulls using the delrin sleeve.

Lloyds Type Approved, RINA, ABS Type Approved, USCG Ignition Protected and ABYC H-27 Side Load approved.

All lights utilize Tritonium Optical lenses, and are supplied with a quick connect system by Deutsch ensuring almost ’fool proof’ installation and compliance with ABYC, E11 regulations.

The Flush Mount from OceanLED has an exceptionally low profile giving it virtually unlimited Hull Mounting options. This light can be retro-fitted into most existing underwater lighting hole cut outs, offering immediate benefits of no Startup power surge, low heat, minimal maintenance and improved light output.

Suitable for Fiberglass, GRP and wooden hulls and now also for use on aluminium/steel hulls using the delrin sleeve.Low profile bezel offering almost unlimited mounting possibilities.

Lloyds Type Approved, RINA, ABS Type Approved, USCG Ignition Protected and ABYC H-27 Side Load approved.

All lights utilize Tritonium Optical lenses, and are supplied with a quick connect system by Deutsch ensuring almost ’fool proof’ installation and compliance with ABYC, E11 regulations.

The original Thru-Hull with the worlds smallest hole cut-out for a thru hull light at only 1"! This light with a 30mm profile head makes it ideal for Transom mount applications. A very quick to fit and effective underwater light.

Suitable for Fiberglass, GRP and wooden hulls and now also available for use on aluminium/steel hulls using the delrin sleeve.

Lloyds Type Approved, RINA, ABS Type Approved, USCG Ignition Protected and ABYC H-27 Side Load approved.

All lights utilize Tritonium Optical lenses, and are supplied with a quick connect system by Deutsch ensuring almost ’fool proof’ installation and compliance with ABYC, E11 regulations.

The Flush Mount from OceanLED has an exceptionally low profile giving it virtually unlimited Hull Mounting options. This light can be retro-fitted into most existing underwater lighting hole cut outs, offering immediate benefits of no Startup power surge, low heat, minimal maintenance and improved light output.

Suitable for Fiberglass, GRP and wooden hulls and now also for use on aluminium/steel hulls using the delrin sleeve.Low profile bezel offering almost unlimited mounting possibilities.

Lloyds Type Approved, RINA, ABS Type Approved, USCG Ignition Protected and ABYC H-27 Side Load approved.

All lights utilize Tritonium Optical lenses, and are supplied with a quick connect system by Deutsch ensuring almost ’fool proof’ installation and compliance with ABYC, E11 regulations.

The Flush Mount from OceanLED has an exceptionally low profile giving it virtually unlimited Hull Mounting options. This light can be retro-fitted into most existing underwater lighting hole cut outs, offering immediate benefits of no Startup power surge, low heat, minimal maintenance and improved light output.

Suitable for Fiberglass, GRP and wooden hulls and now also for use on aluminium/steel hulls using the delrin sleeve.Low profile bezel offering almost unlimited mounting possibilities.

Lloyds Type Approved, RINA, ABS Type Approved, USCG Ignition Protected and ABYC H-27 Side Load approved.

All lights utilize Tritonium Optical lenses, and are supplied with a quick connect system by Deutsch ensuring almost ’fool proof’ installation and compliance with ABYC, E11 regulations.

The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light ? either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 20% brighter than its predecessor the 2010 the 60i is equivalent to any 100w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65?), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

• All-in-One Technology
• Versatile Mounting Options
• Ultra-High Light Output - equal to 100w Xenon
• 12/24vDC
• 40,000+ Hour Life
• Aluminium Bronze AB2
• Plug & Play
• Factory Sealed Unit
• No Breakable Parts
• Reverse Polarity Protected
• 2200 Fixture lumens
• 60° beam

The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light ? either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 20% brighter than its predecessor the 2010 the 60i is equivalent to any 100w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65?), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

• All-in-One Technology
• Versatile Mounting Options
• Ultra-High Light Output - equal to 100w Xenon
• 12/24vDC
• 40,000+ Hour Life
• Aluminium Bronze AB2
• Plug & Play
• Factory Sealed Unit
• No Breakable Parts
• Reverse Polarity Protected
• 2200 Fixture lumens
• 60° beam

The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light ? either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 20% brighter than its predecessor the 2010 the 60i is equivalent to any 100w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65?), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

• All-in-One Technology
• Versatile Mounting Options
• Ultra-High Light Output - equal to 100w Xenon
• 12/24vDC
• 40,000+ Hour Life
• Aluminium Bronze AB2
• Plug & Play
• Factory Sealed Unit
• No Breakable Parts
• Reverse Polarity Protected
• 2200 Fixture lumens
• 60° beam

The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light ? either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 40% brighter than its predecessor the 1520 the 30i is equivalent to any 50w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65’), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

• All-in-One Technology
• Versatile Mounting Options
• Ultra-High Light Output - equal to 50w Xenon
• 12/24vDC
• 40,000+ Hour Life
• Aluminium Bronze AB2
• Plug & Play
• Factory Sealed Unit
• No Breakable Parts
• Reverse Polarity Protected

The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light ? either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 40% brighter than its predecessor the 1520 the 30i is equivalent to any 50w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65’), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

• All-in-One Technology
• Versatile Mounting Options
• Ultra-High Light Output - equal to 50w Xenon
• 12/24vDC
• 40,000+ Hour Life
• Aluminium Bronze AB2
• Plug & Play
• Factory Sealed Unit
• No Breakable Parts
• Reverse Polarity Protected

The New Hybrid Series, the next generation of underwater lighting has arrived from industry leader OceanLED. The Hybrids all-in-one technology marks it as the first high powered underwater LED light without any external power supplies or driver boxes. Its new integrated built-in driver and electronics eliminate installation complications of the past and results in a much cleaner, faster installation. Taking the 1" thru hull concept even further the Hybrid model now has the most versatile mounting method on an underwater light ? either surface mount the fixture on to the hull with a small 1" hole for cable access or thread the optional thru hull locking stem on to the rear of the light body and use as a traditional thru hull. When space is a premium you can simply cut the stem to size and re-attach to the light fixture, for a customized fit. Hybrids yield ultra-high light output, almost 40% brighter than its predecessor the 1520 the 30i is equivalent to any 50w Xenon underwater light on the market and most high powered LED competing lights. Suitable for Fiberglass, GRP and wooden hulls up to 20m (65’), and also usable on aluminium/steel hulls/brackets using the Delrin Sleeve option.

• All-in-One Technology
• Versatile Mounting Options
• Ultra-High Light Output - equal to 50w Xenon
• 12/24vDC
• 40,000+ Hour Life
• Aluminium Bronze AB2
• Plug & Play
• Factory Sealed Unit
• No Breakable Parts
• Reverse Polarity Protected

The New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic Series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T6 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as Dock Lighting.

Ultra low power draw, no start-up current required.

• 3/8? Hole in Hull
• Equal to 80w Halogen
• 12/24vDC
• 40,000+ Hour Life
• Chemically Resistant Polymer
• Twin Core Wire
• Factory Sealed Unit
• No Breakable Parts

Mounting Recommendations T6

Boat size: up to 9m (30?)
Transom spacing: 0.5-1m (2-3?)
Transom quantity: 2-4
Hull spacing: 0.5-1.2m (2-4?)
For above and below water use

Technical

Light output: equivalent to 80W Halogen
Fixture Lumens*: (total light output from a finished fixture) 400
Typical LED life expectancy: 40,000+ Hours
Minimum-Maximum operating voltage DC: 9-32vDC
Current / Amp draw (DC): 12vDC 0.5A 24vDC 0.3A
Approx. light penetration (avg. water quality): 3.5m (11.5?)
Approx. Light penetration (perfect water quality): up to 9+m (30?)
Driver type Internal

Physical

Length of fixture: 155mm (61/8?)
Width of fixture: 50mm (2?)
Profile (height) of fixture: 21.5mm (3/4?)
Total weight: 155grms (5.4oz)
Extension cable length (standard): 2m (61/2?)
Hole cut-out for cable entry: 9mm (3/8?)
Material Chemically resistant optical polymer
Lens Impact resistant lens

The New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic Series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T6 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as Dock Lighting.

Ultra low power draw, no start-up current required.

• 3/8? Hole in Hull
• Equal to 80w Halogen
• 12/24vDC
• 40,000+ Hour Life
• Chemically Resistant Polymer
• Twin Core Wire
• Factory Sealed Unit
• No Breakable Parts

Mounting Recommendations T6

Boat size: up to 9m (30?)
Transom spacing: 0.5-1m (2-3?)
Transom quantity: 2-4
Hull spacing: 0.5-1.2m (2-4?)
For above and below water use

Technical

Light output: equivalent to 80W Halogen
Fixture Lumens*: (total light output from a finished fixture) 400
Typical LED life expectancy: 40,000+ Hours
Minimum-Maximum operating voltage DC: 9-32vDC
Current / Amp draw (DC): 12vDC 0.5A 24vDC 0.3A
Approx. light penetration (avg. water quality): 3.5m (11.5?)
Approx. Light penetration (perfect water quality): up to 9+m (30?)
Driver type Internal

Physical

Length of fixture: 155mm (61/8?)
Width of fixture: 50mm (2?)
Profile (height) of fixture: 21.5mm (3/4?)
Total weight: 155grms (5.4oz)
Extension cable length (standard): 2m (61/2?)
Hole cut-out for cable entry: 9mm (3/8?)
Material Chemically resistant optical polymer
Lens Impact resistant lens

The New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic Series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T6 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as Dock Lighting.

Ultra low power draw, no start-up current required.

• 3/8? Hole in Hull
• Equal to 80w Halogen
• 12/24vDC
• 40,000+ Hour Life
• Chemically Resistant Polymer
• Twin Core Wire
• Factory Sealed Unit
• No Breakable Parts

Mounting Recommendations T6

Boat size: up to 9m (30?)
Transom spacing: 0.5-1m (2-3?)
Transom quantity: 2-4
Hull spacing: 0.5-1.2m (2-4?)
For above and below water use

Technical

Light output: equivalent to 80W Halogen
Fixture Lumens*: (total light output from a finished fixture) 400
Typical LED life expectancy: 40,000+ Hours
Minimum-Maximum operating voltage DC: 9-32vDC
Current / Amp draw (DC): 12vDC 0.5A 24vDC 0.3A
Approx. light penetration (avg. water quality): 3.5m (11.5?)
Approx. Light penetration (perfect water quality): up to 9+m (30?)
Driver type Internal

Physical

Length of fixture: 155mm (61/8?)
Width of fixture: 50mm (2?)
Profile (height) of fixture: 21.5mm (3/4?)
Total weight: 155grms (5.4oz)
Extension cable length (standard): 2m (61/2?)
Hole cut-out for cable entry: 9mm (3/8?)
Material Chemically resistant optical polymer
Lens Impact resistant lens

bThe New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic Series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T6 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series.

Ultra low power draw, no start-up current required.

• 3/8? Hole in Hull
• Equal to 50w Halogen
• 12vDC ONLY
• 40,000+ Hour Life
• Chemically Resistant Polymer
• Twin Core Wire
• Factory Sealed Unit
• No Breakable Parts

bThe New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic Series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T6 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series.

Ultra low power draw, no start-up current required.

• 3/8? Hole in Hull
• Equal to 50w Halogen
• 12vDC ONLY
• 40,000+ Hour Life
• Chemically Resistant Polymer
• Twin Core Wire
• Factory Sealed Unit
• No Breakable Parts

bThe New Amphibian Trailer Boat Series of LED lighting is the ideal choice for the trailered boat. Equally as bright as the Amphibian Classic Series but without the sea growth resistant Tritonium Lens intended for boats that are in the water longer term. A great value!

The Amphibian T6 is exceptionally easy to install and may be used above or below the water line such as on the transom, hull, engine brackets, t-top, under the gunnels, and even on the trailer for night launching. Not intended for use as Dock Lighting; please see our Dock Light Series.

Ultra low power draw, no start-up current required.

• 3/8? Hole in Hull
• Equal to 50w Halogen
• 12vDC ONLY
• 40,000+ Hour Life
• Chemically Resistant Polymer
• Twin Core Wire
• Factory Sealed Unit
• No Breakable Parts

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A3Pro underwater light rivals any 75 watt Halogen on the market and with 8 times the power savings.

The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way.

Exceptionally easy to install and versatile enough to be mounted onto any transom or hull.

Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• 3/8" Hole in Hull
• Equal to 75w Halogen
• 12vDC ONLY
• 40,000+ Hour Life
• Chemically Resistant Polymer
• Twin Core Wire
• Factory Sealed Unit
• No Breakable Parts

Mounting Recommendations A3 Pro

Boat size up to: 9m (30’)
Transom spacing: 0.5-1m (2-3’)
Transom quantity: 2-4
Hull spacing: 0.5-1.2m (2-4’)
For above and below water use

Technical

Light output equivalent to: 75W Halogen
Fixture Lumens* (total light output from a finished fixture): 350
Typical LED life expectancy: 40,000+ Hours
Minimum-Maximum operating voltage: DC 9-15vDC
Current / Amp draw (DC): 12vDC 0.5A
Approx. light penetration (avg. water quality): 4m (13’)
Approx. Light penetration (perfect water quality) up to: 9+m (30’)
Driver type Internal

Physical

Length of fixture: 92mm (35/8")
Width of fixture: 50mm (2")
Profile (height) of fixture: 21.5mm (3/4?)
Total weight: 110grms (3.8oz)
Extension cable length (standard): 2m (61/2’)
Hole cut-out for cable entry: 9mm (3/8")
Material: Chemically resistant optical polymer
Lens: Tritonium Optical Lens

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A3Pro underwater light rivals any 75 watt Halogen on the market and with 8 times the power savings.

The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way.

Exceptionally easy to install and versatile enough to be mounted onto any transom or hull.

Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• 3/8" Hole in Hull
• Equal to 75w Halogen
• 12vDC ONLY
• 40,000+ Hour Life
• Chemically Resistant Polymer
• Twin Core Wire
• Factory Sealed Unit
• No Breakable Parts

Mounting Recommendations A3 Pro

Boat size up to: 9m (30’)
Transom spacing: 0.5-1m (2-3’)
Transom quantity: 2-4
Hull spacing: 0.5-1.2m (2-4’)
For above and below water use

Technical

Light output equivalent to: 75W Halogen
Fixture Lumens* (total light output from a finished fixture): 350
Typical LED life expectancy: 40,000+ Hours
Minimum-Maximum operating voltage: DC 9-15vDC
Current / Amp draw (DC): 12vDC 0.5A
Approx. light penetration (avg. water quality): 4m (13’)
Approx. Light penetration (perfect water quality) up to: 9+m (30’)
Driver type Internal

Physical

Length of fixture: 92mm (35/8")
Width of fixture: 50mm (2")
Profile (height) of fixture: 21.5mm (3/4?)
Total weight: 110grms (3.8oz)
Extension cable length (standard): 2m (61/2’)
Hole cut-out for cable entry: 9mm (3/8")
Material: Chemically resistant optical polymer
Lens: Tritonium Optical Lens

• Minimal Power Requirements
• Chemically Inert, Rust Free Body
• 40,000 Hours Lifespan
• Tritonium Lens - Scratch & Sea Growth Resistant
• No External Parts
• 3/8? Thru Hull Installation
• For Underwater Use Only!
• Brighter than a 50 watt
• Xenon Underwater Light with up to 8 times the power savings!
• Almost twice as bright as the original!

The new A12 Pro from OceanLED raises the bar yet again for all underwater lighting on the market. The original Amphibian range, (A3, A6 and A12) were designed with the specific purpose of running in and out of water, however with the singular purpose of being used underwater the power can be substantially turned up as the water cooling is consistent. In doing this the A12 becomes almost 75% brighter than a standard A12 which means it will out perform any competing LED underwater light on the market but more importantly rival any 50 watt Xenon bulb style underwater light.

Issued with an exclusive Gun-Metal colored insert the A12 still holds all the normal characteristics of the standard A12 such as thermal protection, Tritonium lens protection, 40,000 hour life and with only a slight increase in power draw. Powered on 12vDC the A12 Pro uses only 1.8 amps and on 24vDC a mere 0.9 amps, which when compared to a xenon bulb at over an 8 amp current draw, the advantages are clear.

Available in Blue, White and Green the A12 Pro is set to re-establish another industry bench mark.

 

• Minimal Power Requirements
• Chemically Inert, Rust Free Body
• 40,000 Hours Lifespan
• Tritonium Lens - Scratch & Sea Growth Resistant
• No External Parts
• 3/8? Thru Hull Installation
• For Underwater Use Only!
• Brighter than a 50 watt
• Xenon Underwater Light with up to 8 times the power savings!
• Almost twice as bright as the original!

The new A12 Pro from OceanLED raises the bar yet again for all underwater lighting on the market. The original Amphibian range, (A3, A6 and A12) were designed with the specific purpose of running in and out of water, however with the singular purpose of being used underwater the power can be substantially turned up as the water cooling is consistent. In doing this the A12 becomes almost 75% brighter than a standard A12 which means it will out perform any competing LED underwater light on the market but more importantly rival any 50 watt Xenon bulb style underwater light.

Issued with an exclusive Gun-Metal colored insert the A12 still holds all the normal characteristics of the standard A12 such as thermal protection, Tritonium lens protection, 40,000 hour life and with only a slight increase in power draw. Powered on 12vDC the A12 Pro uses only 1.8 amps and on 24vDC a mere 0.9 amps, which when compared to a xenon bulb at over an 8 amp current draw, the advantages are clear.

Available in Blue, White and Green the A12 Pro is set to re-establish another industry bench mark.

 

• Minimal Power Requirements
• Chemically Inert, Rust Free Body
• 40,000 Hours Lifespan
• Tritonium Lens - Scratch & Sea Growth Resistant
• No External Parts
• 3/8? Thru Hull Installation
• For Underwater Use Only!
• Brighter than a 50 watt
• Xenon Underwater Light with up to 8 times the power savings!
• Almost twice as bright as the original!

The new A12 Pro from OceanLED raises the bar yet again for all underwater lighting on the market. The original Amphibian range, (A3, A6 and A12) were designed with the specific purpose of running in and out of water, however with the singular purpose of being used underwater the power can be substantially turned up as the water cooling is consistent. In doing this the A12 becomes almost 75% brighter than a standard A12 which means it will out perform any competing LED underwater light on the market but more importantly rival any 50 watt Xenon bulb style underwater light.

Issued with an exclusive Gun-Metal colored insert the A12 still holds all the normal characteristics of the standard A12 such as thermal protection, Tritonium lens protection, 40,000 hour life and with only a slight increase in power draw. Powered on 12vDC the A12 Pro uses only 1.8 amps and on 24vDC a mere 0.9 amps, which when compared to a xenon bulb at over an 8 amp current draw, the advantages are clear.

Available in Blue, White and Green the A12 Pro is set to re-establish another industry bench mark.

 

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A6Pro underwater light rivals any 35 watt Xenon on the market and with 8 times the power savings.

The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way.

Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as Dock.

Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• 3/8" Hole in Hull
• Equal to 35w Xenon
• 12/24vDC
• 40,000+ Hour Life
• Chemically Resistant Polymer
• Twin Core Wire
• Factory Sealed Unit
• No Breakable Parts

Mounting Recommendations A6 Pro

Boat size up to: 10m (35’)
Transom spacing: 0.5-1.2m (2-4’)
Transom quantity: 2-4
Hull spacing: 0.5-1.2m (2-4’)
Installation depth (to top of fixture): 10-20cm (4-8")

Technical

Light output equivalent to: 35W Xenon
Fixture Lumens* (total light output from a finished fixture): 700
Typical LED life expectancy: 40,000+ Hours
Minimum-Maximum operating voltage: DC 9-32vDC
Current / Amp draw (DC): 12vDC 0.9A 24vDC 0.5A
Approx. light penetration (avg. water quality): 5m (16’)
Approx. Light penetration (perfect water quality) up to: 13+m (42’)
Driver type Internal

Physical

Length of fixture: 155mm (61/8")
Width of fixture: 50mm (2")
Profile (height) of fixture: 21.5mm (3/4")
Total weight: 155grms (5.4oz)
Extension cable length: (standard) 2m (61/2’)
Hole cut-out for cable entry: 9mm (3/8")
Material: Chemically resistant optical polymer
Lens: Tritonium Optical Lens

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A6Pro underwater light rivals any 35 watt Xenon on the market and with 8 times the power savings.

The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way.

Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as Dock.

Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• 3/8" Hole in Hull
• Equal to 35w Xenon
• 12/24vDC
• 40,000+ Hour Life
• Chemically Resistant Polymer
• Twin Core Wire
• Factory Sealed Unit
• No Breakable Parts

Mounting Recommendations A6 Pro

Boat size up to: 10m (35’)
Transom spacing: 0.5-1.2m (2-4’)
Transom quantity: 2-4
Hull spacing: 0.5-1.2m (2-4’)
Installation depth (to top of fixture): 10-20cm (4-8")

Technical

Light output equivalent to: 35W Xenon
Fixture Lumens* (total light output from a finished fixture): 700
Typical LED life expectancy: 40,000+ Hours
Minimum-Maximum operating voltage: DC 9-32vDC
Current / Amp draw (DC): 12vDC 0.9A 24vDC 0.5A
Approx. light penetration (avg. water quality): 5m (16’)
Approx. Light penetration (perfect water quality) up to: 13+m (42’)
Driver type Internal

Physical

Length of fixture: 155mm (61/8")
Width of fixture: 50mm (2")
Profile (height) of fixture: 21.5mm (3/4")
Total weight: 155grms (5.4oz)
Extension cable length: (standard) 2m (61/2’)
Hole cut-out for cable entry: 9mm (3/8")
Material: Chemically resistant optical polymer
Lens: Tritonium Optical Lens

The Amphibian Pro Series raises the bar on the original Amphibian range with an increase in brightness by 75%! The A6Pro underwater light rivals any 35 watt Xenon on the market and with 8 times the power savings.

The Amphibian Pro Series is for underwater use only however, due to its Active Thermal Control, a built-in temperature monitoring system, they can be used while under way.

Exceptionally easy to install and versatile enough to be mounted onto any transom or hull. Not intended for use as Dock.

Maintenance is easy, just wipe away sea growth from its scratch resistant Tritonium Lens.

• 3/8" Hole in Hull
• Equal to 35w Xenon
• 12/24vDC
• 40,000+ Hour Life
• Chemically Resistant Polymer
• Twin Core Wire
• Factory Sealed Unit
• No Breakable Parts

Mounting Recommendations A6 Pro

Boat size up to: 10m (35’)
Transom spacing: 0.5-1.2m (2-4’)
Transom quantity: 2-4
Hull spacing: 0.5-1.2m (2-4’)
Installation depth (to top of fixture): 10-20cm (4-8")

Technical

Light output equivalent to: 35W Xenon
Fixture Lumens* (total light output from a finished fixture): 700
Typical LED life expectancy: 40,000+ Hours
Minimum-Maximum operating voltage: DC 9-32vDC
Current / Amp draw (DC): 12vDC 0.9A 24vDC 0.5A
Approx. light penetration (avg. water quality): 5m (16’)
Approx. Light penetration (perfect water quality) up to: 13+m (42’)
Driver type Internal

Physical

Length of fixture: 155mm (61/8")
Width of fixture: 50mm (2")
Profile (height) of fixture: 21.5mm (3/4")
Total weight: 155grms (5.4oz)
Extension cable length: (standard) 2m (61/2’)
Hole cut-out for cable entry: 9mm (3/8")
Material: Chemically resistant optical polymer
Lens: Tritonium Optical Lens

OceanLED is the leading manufacturer and designer of underwater lighting products and the unique Amphibian range launches the world?s first lighting collection designed to be used both in and out of the water.

OceanLED has created the Amphibians based on the increasing demand for affordable LED lights for the boating industry; subsequently providing consumers with a high quality, low priced underwater lighting solution without sacrificing on quality or the visual effect of the lights in the ocean.

The Amphibian range has been designed with a unique linear shape, versatile enough to be mounted onto any transom and requiring just a 3/8th hole for the cable entry. The Amphibians are exceptionally easy to install and can be used on a variety of surfaces such as trim tabs, engine brackets or even on boat trailers for night launching.

Despite the Amphibians small size, they are extremely powerful making them comparable to competitors? halogen and Xenon underwater lighting models. Using the very latest LED technology, the Amphibians have an ultra low power draw with no start up current required, over 50,000 hour LED life and pure unfiltered colors designed to make an impact on any boat of any size. Extensive OceanLED research has also enabled all electronics to be built directly into the Amphibians, alleviating the need for an external LED driver.

Once fitted, the Amphibians are virtually maintenance free. The lights are injection moulded in Delnaeco Polymer ? a state-of-the-art Polymer that is resistant to almost all known solvents and adhesives, and is completely corrosion proof. In addition, OceanLED is renowned for using Tritonium glass. These unique glass lenses have been specifically designed by OceanLED and Tritonium Optical Technologies (a research laboratory specialising in optical systems) to inhibit barnacle build up and ensure that the Polymer light lens cannot be scratched like other plastic underwater lights.

The Amphibians are exceptionally easy to install and can be used anywhere, such as:

• Transoms
• Engine Brackets
• Under the gunnels
• Trim tabs
• T-Tops
• Boat trailers for night launching.
• ROVs
• Tail gates

OceanLED is the leading manufacturer and designer of underwater lighting products and the unique Amphibian range launches the world?s first lighting collection designed to be used both in and out of the water.

OceanLED has created the Amphibians based on the increasing demand for affordable LED lights for the boating industry; subsequently providing consumers with a high quality, low priced underwater lighting solution without sacrificing on quality or the visual effect of the lights in the ocean.

The Amphibian range has been designed with a unique linear shape, versatile enough to be mounted onto any transom and requiring just a 3/8th hole for the cable entry. The Amphibians are exceptionally easy to install and can be used on a variety of surfaces such as trim tabs, engine brackets or even on boat trailers for night launching.

Despite the Amphibians small size, they are extremely powerful making them comparable to competitors? halogen and Xenon underwater lighting models. Using the very latest LED technology, the Amphibians have an ultra low power draw with no start up current required, over 50,000 hour LED life and pure unfiltered colors designed to make an impact on any boat of any size. Extensive OceanLED research has also enabled all electronics to be built directly into the Amphibians, alleviating the need for an external LED driver.

Once fitted, the Amphibians are virtually maintenance free. The lights are injection moulded in Delnaeco Polymer ? a state-of-the-art Polymer that is resistant to almost all known solvents and adhesives, and is completely corrosion proof. In addition, OceanLED is renowned for using Tritonium glass. These unique glass lenses have been specifically designed by OceanLED and Tritonium Optical Technologies (a research laboratory specialising in optical systems) to inhibit barnacle build up and ensure that the Polymer light lens cannot be scratched like other plastic underwater lights.

The Amphibians are exceptionally easy to install and can be used anywhere, such as:

• Transoms
• Engine Brackets
• Under the gunnels
• Trim tabs
• T-Tops
• Boat trailers for night launching.
• ROVs
• Tail gates

OceanLED is the leading manufacturer and designer of underwater lighting products and the unique Amphibian range launches the world?s first lighting collection designed to be used both in and out of the water.

OceanLED has created the Amphibians based on the increasing demand for affordable LED lights for the boating industry; subsequently providing consumers with a high quality, low priced underwater lighting solution without sacrificing on quality or the visual effect of the lights in the ocean.

The Amphibian range has been designed with a unique linear shape, versatile enough to be mounted onto any transom and requiring just a 3/8th hole for the cable entry. The Amphibians are exceptionally easy to install and can be used on a variety of surfaces such as trim tabs, engine brackets or even on boat trailers for night launching.

Despite the Amphibians small size, they are extremely powerful making them comparable to competitors? halogen and Xenon underwater lighting models. Using the very latest LED technology, the Amphibians have an ultra low power draw with no start up current required, over 50,000 hour LED life and pure unfiltered colors designed to make an impact on any boat of any size. Extensive OceanLED research has also enabled all electronics to be built directly into the Amphibians, alleviating the need for an external LED driver.

Once fitted, the Amphibians are virtually maintenance free. The lights are injection moulded in Delnaeco Polymer ? a state-of-the-art Polymer that is resistant to almost all known solvents and adhesives, and is completely corrosion proof. In addition, OceanLED is renowned for using Tritonium glass. These unique glass lenses have been specifically designed by OceanLED and Tritonium Optical Technologies (a research laboratory specialising in optical systems) to inhibit barnacle build up and ensure that the Polymer light lens cannot be scratched like other plastic underwater lights.

The Amphibians are exceptionally easy to install and can be used anywhere, such as:

• Transoms
• Engine Brackets
• Under the gunnels
• Trim tabs
• T-Tops
• Boat trailers for night launching.
• ROVs
• Tail gates

OceanLED is the leading manufacturer and designer of underwater lighting products and the unique Amphibian range launches the world?s first lighting collection designed to be used both in and out of the water.

OceanLED has created the Amphibians based on the increasing demand for affordable LED lights for the boating industry; subsequently providing consumers with a high quality, low priced underwater lighting solution without sacrificing on quality or the visual effect of the lights in the ocean.

The Amphibian range has been designed with a unique linear shape, versatile enough to be mounted onto any transom and requiring just a 3/8th hole for the cable entry. The Amphibians are exceptionally easy to install and can be used on a variety of surfaces such as trim tabs, engine brackets or even on boat trailers for night launching.

Despite the Amphibians small size, they are extremely powerful making them comparable to competitors? halogen and Xenon underwater lighting models. Using the very latest LED technology, the Amphibians have an ultra low power draw with no start up current required, over 50,000 hour LED life and pure unfiltered colors designed to make an impact on any boat of any size. Extensive OceanLED research has also enabled all electronics to be built directly into the Amphibians, alleviating the need for an external LED driver.

Once fitted, the Amphibians are virtually maintenance free. The lights are injection moulded in Delnaeco Polymer ? a state-of-the-art Polymer that is resistant to almost all known solvents and adhesives, and is completely corrosion proof. In addition, OceanLED is renowned for using Tritonium glass. These unique glass lenses have been specifically designed by OceanLED and Tritonium Optical Technologies (a research laboratory specialising in optical systems) to inhibit barnacle build up and ensure that the Polymer light lens cannot be scratched like other plastic underwater lights.

The Amphibians are exceptionally easy to install and can be used anywhere, such as:

• Transoms
• Engine Brackets
• Under the gunnels
• Trim tabs
• T-Tops
• Boat trailers for night launching.
• ROVs
• Tail gates

OceanLED is the leading manufacturer and designer of underwater lighting products and the unique Amphibian range launches the world?s first lighting collection designed to be used both in and out of the water.

OceanLED has created the Amphibians based on the increasing demand for affordable LED lights for the boating industry; subsequently providing consumers with a high quality, low priced underwater lighting solution without sacrificing on quality or the visual effect of the lights in the ocean.

The Amphibian range has been designed with a unique linear shape, versatile enough to be mounted onto any transom and requiring just a 3/8th hole for the cable entry. The Amphibians are exceptionally easy to install and can be used on a variety of surfaces such as trim tabs, engine brackets or even on boat trailers for night launching.

Despite the Amphibians small size, they are extremely powerful making them comparable to competitors? halogen and Xenon underwater lighting models. Using the very latest LED technology, the Amphibians have an ultra low power draw with no start up current required, over 50,000 hour LED life and pure unfiltered colors designed to make an impact on any boat of any size. Extensive OceanLED research has also enabled all electronics to be built directly into the Amphibians, alleviating the need for an external LED driver.

Once fitted, the Amphibians are virtually maintenance free. The lights are injection moulded in Delnaeco Polymer ? a state-of-the-art Polymer that is resistant to almost all known solvents and adhesives, and is completely corrosion proof. In addition, OceanLED is renowned for using Tritonium glass. These unique glass lenses have been specifically designed by OceanLED and Tritonium Optical Technologies (a research laboratory specialising in optical systems) to inhibit barnacle build up and ensure that the Polymer light lens cannot be scratched like other plastic underwater lights.

The Amphibians are exceptionally easy to install and can be used anywhere, such as:

• Transoms
• Engine Brackets
• Under the gunnels
• Trim tabs
• T-Tops
• Boat trailers for night launching.
• ROVs
• Tail gates

OceanLED is the leading manufacturer and designer of underwater lighting products and the unique Amphibian range launches the world?s first lighting collection designed to be used both in and out of the water.

OceanLED has created the Amphibians based on the increasing demand for affordable LED lights for the boating industry; subsequently providing consumers with a high quality, low priced underwater lighting solution without sacrificing on quality or the visual effect of the lights in the ocean.

The Amphibian range has been designed with a unique linear shape, versatile enough to be mounted onto any transom and requiring just a 3/8th hole for the cable entry. The Amphibians are exceptionally easy to install and can be used on a variety of surfaces such as trim tabs, engine brackets or even on boat trailers for night launching.

Despite the Amphibians small size, they are extremely powerful making them comparable to competitors? halogen and Xenon underwater lighting models. Using the very latest LED technology, the Amphibians have an ultra low power draw with no start up current required, over 50,000 hour LED life and pure unfiltered colors designed to make an impact on any boat of any size. Extensive OceanLED research has also enabled all electronics to be built directly into the Amphibians, alleviating the need for an external LED driver.

Once fitted, the Amphibians are virtually maintenance free. The lights are injection moulded in Delnaeco Polymer ? a state-of-the-art Polymer that is resistant to almost all known solvents and adhesives, and is completely corrosion proof. In addition, OceanLED is renowned for using Tritonium glass. These unique glass lenses have been specifically designed by OceanLED and Tritonium Optical Technologies (a research laboratory specialising in optical systems) to inhibit barnacle build up and ensure that the Polymer light lens cannot be scratched like other plastic underwater lights.

The Amphibians are exceptionally easy to install and can be used anywhere, such as:

• Transoms
• Engine Brackets
• Under the gunnels
• Trim tabs
• T-Tops
• Boat trailers for night launching.
• ROVs
• Tail gates

OceanLED is the leading manufacturer and designer of underwater lighting products and the unique Amphibian range launches the world?s first lighting collection designed to be used both in and out of the water.

OceanLED has created the Amphibians based on the increasing demand for affordable LED lights for the boating industry; subsequently providing consumers with a high quality, low priced underwater lighting solution without sacrificing on quality or the visual effect of the lights in the ocean.

The Amphibian range has been designed with a unique linear shape, versatile enough to be mounted onto any transom and requiring just a 3/8th hole for the cable entry. The Amphibians are exceptionally easy to install and can be used on a variety of surfaces such as trim tabs, engine brackets or even on boat trailers for night launching.

Despite the Amphibians small size, they are extremely powerful making them comparable to competitors? halogen and Xenon underwater lighting models. Using the very latest LED technology, the Amphibians have an ultra low power draw with no start up current required, over 50,000 hour LED life and pure unfiltered colors designed to make an impact on any boat of any size. Extensive OceanLED research has also enabled all electronics to be built directly into the Amphibians, alleviating the need for an external LED driver.

Once fitted, the Amphibians are virtually maintenance free. The lights are injection moulded in Delnaeco Polymer ? a state-of-the-art Polymer that is resistant to almost all known solvents and adhesives, and is completely corrosion proof. In addition, OceanLED is renowned for using Tritonium glass. These unique glass lenses have been specifically designed by OceanLED and Tritonium Optical Technologies (a research laboratory specialising in optical systems) to inhibit barnacle build up and ensure that the Polymer light lens cannot be scratched like other plastic underwater lights.

The Amphibians are exceptionally easy to install and can be used anywhere, such as:

• Transoms
• Engine Brackets
• Under the gunnels
• Trim tabs
• T-Tops
• Boat trailers for night launching.
• ROVs
• Tail gates

OceanLED is the leading manufacturer and designer of underwater lighting products and the unique Amphibian range launches the world?s first lighting collection designed to be used both in and out of the water.

OceanLED has created the Amphibians based on the increasing demand for affordable LED lights for the boating industry; subsequently providing consumers with a high quality, low priced underwater lighting solution without sacrificing on quality or the visual effect of the lights in the ocean.

The Amphibian range has been designed with a unique linear shape, versatile enough to be mounted onto any transom and requiring just a 3/8th hole for the cable entry. The Amphibians are exceptionally easy to install and can be used on a variety of surfaces such as trim tabs, engine brackets or even on boat trailers for night launching.

Despite the Amphibians small size, they are extremely powerful making them comparable to competitors? halogen and Xenon underwater lighting models. Using the very latest LED technology, the Amphibians have an ultra low power draw with no start up current required, over 50,000 hour LED life and pure unfiltered colors designed to make an impact on any boat of any size. Extensive OceanLED research has also enabled all electronics to be built directly into the Amphibians, alleviating the need for an external LED driver.

Once fitted, the Amphibians are virtually maintenance free. The lights are injection moulded in Delnaeco Polymer ? a state-of-the-art Polymer that is resistant to almost all known solvents and adhesives, and is completely corrosion proof. In addition, OceanLED is renowned for using Tritonium glass. These unique glass lenses have been specifically designed by OceanLED and Tritonium Optical Technologies (a research laboratory specialising in optical systems) to inhibit barnacle build up and ensure that the Polymer light lens cannot be scratched like other plastic underwater lights.

The Amphibians are exceptionally easy to install and can be used anywhere, such as:

• Transoms
• Engine Brackets
• Under the gunnels
• Trim tabs
• T-Tops
• Boat trailers for night launching.
• ROVs
• Tail gates

Simply bring the power feed into one IP68 terminal box, then quickly connect all the LED drivers in one location
with the Plug & Play Deutsch connector. For DC voltage only.

Trim Tab Light

The Trim Tab Light, which has proved to be a popular aftermarket product, is built out of thermal polymer, which means it?s completely corrosion-free. Designed to mount on top of your trim tabs, it is ideal for those people who don?t want to drill a hole in their boat, or for small trailerable boats. The Trim Tab Light can also be mounted on an L Bracket for boats that don?t have trim tabs.

Available in Ultra Blue, Ultra Green and Brilliant White, this product is recommended for boats up to 30 feet.

Trim Tab Light Specifications

• High-tech polymer housing
• Mounts to trim tab or L bracket.
• Low DC power consumption.
• 12 or volt DC power source
• Draws less than amp @12 volt DC
• Low heat emission
• Can be run out of water (while boat is planning)
• 3 x Long life high output LED?s
• No bonding required
• No corrosion
• 3.7 metre. (12ft.) tined underwater cable
• Available in Ultra Blue, Ultra Green and brilliant White
• 2 year warranty
• Australian designed and manufactured

Trim Tab Light

The Trim Tab Light, which has proved to be a popular aftermarket product, is built out of thermal polymer, which means it?s completely corrosion-free. Designed to mount on top of your trim tabs, it is ideal for those people who don?t want to drill a hole in their boat, or for small trailerable boats. The Trim Tab Light can also be mounted on an L Bracket for boats that don?t have trim tabs.

Available in Ultra Blue, Ultra Green and Brilliant White, this product is recommended for boats up to 30 feet.

Trim Tab Light Specifications

• High-tech polymer housing
• Mounts to trim tab or L bracket.
• Low DC power consumption.
• 12 or volt DC power source
• Draws less than amp @12 volt DC
• Low heat emission
• Can be run out of water (while boat is planning)
• 3 x Long life high output LED?s
• No bonding required
• No corrosion
• 3.7 metre. (12ft.) tined underwater cable
• Available in Ultra Blue, Ultra Green and brilliant White
• 2 year warranty
• Australian designed and manufactured

Mount your OceanLED Amphibian lights almost anywhere! Screw fix or zip tie to T-tops, spreaders, outriggers, trim tabs, pontoons, masts, trailers, engine cowlings, on deck, as well as in landscape applications or for wall-wash effects. The clamp assembly allows for affixing to round pipe.  316L Stainless Steel bolts and nylon nuts
 

Mount your OceanLED Amphibian lights almost anywhere! Screw fix or zip tie to T-tops, spreaders, outriggers, trim tabs, pontoons, masts, trailers, engine cowlings, on deck, as well as in landscape applications or for wall-wash effects. The clamp assembly allows for affixing to round pipe.  316L Stainless Steel bolts and nylon nuts
 

Mount your OceanLED Amphibian lights almost anywhere! Screw fix or zip tie to T-tops, spreaders, outriggers, trim tabs, pontoons, masts, trailers, engine cowlings, on deck, as well as in landscape applications or for wall-wash effects. The clamp assembly allows for affixing to round pipe.  316L Stainless Steel bolts and nylon nuts
 

LIET Features

Long Life Components.
Only components that have at least the same life expectancy as the LED’s are used by OceanLED, this is a critical area that is generally overlooked by most manufacturers.

Low Touch Temperature.
All surfaces of LIET are safe to touch even after being on for extended periods of time, and have no risk of fire or burning.

Intelligent Lighting System.
Each LIET fixture contains self-diagnostic indicators to ensure swift system fault diagnosis, such as over/under voltage and over temperature, as well as protection measures to ensure no damage is sustained by the light. A flashing yellow LED indicates power under/over voltage. A blinking red LED indicates over temperature. There will be a progressive thermal shut down of LIET before it switches off.

High Frequency Dimmers.
This ensures that flicker free dimming is achieved over the entire output range, providing an enhanced illumination when compared to low frequency dimming techniques. Low frequency dimming can also be the cause of eye fatigue and headaches following exposure to flickering for extended periods of time.

No Noise Output.
This ensures that any unpleasant background humming or whistling, that can be frequently heard with conventional lighting, is eliminated.


No Toxic Substances.
All the materials used in LIET are RoHS compliant ? they do not contain any hazardous materials, such as mercury, lead, or cadmium, and so there will be no leaching of harmful substances into the environment at the end of the product?s life.

Environmentally Friendly.
The use of LIET will dramatically aid efforts to reduce carbon footprints. Liet has low energy usage, low heat emissions and is a hugely efficient lighting fixture.

Colors Available (Kelvin Temperatures)

When a weld-in underwater lighting fixture is not an option, use the Delrin Isolation Sleeve to isolate the underwater light or camera from the aluminum or steel hull. Designed as an accessory to the Hybrid 60i series.

When a weld-in underwater lighting fixture is not an option, use the Delrin Isolation Sleeve to isolate the underwater light or camera from the aluminum or steel hull. Designed as an accessory to the Hybrid 30i series.

Capture the magic of your own underwater aquarium beneath your boat with the superior quality EYES by OceanLED. Watch on your salon TV or Plasma screen all the nightlife around, be amazed at the variety of fish and sea life attracted to the LED underwater lights.

Competition Sportfishing is starting to require video evidence of catches and so EYES are the perfect accessory to ensure you win!

Team Get Lit, on a 53’ Viking have 4 EYES installed around the transom of the boat to capture every moment of action.

EYES can also be used in conjunction with the onboard security system for your vessel offering 24 hour underwater surveillance.

EYES are designed for fiberglass (GRP) hulls and can be fitted to aluminum or Steel hulls utilizing the optional Delrin Isolating sleeve.

We can also incorporate EYES into our Weld-IN fixtures for metal hulled vessels on special request.
 

Amphibian T3s Drain Plug - Underwater Lighting Experience

The Amphibian Drain Plug Light uses a 316 Stainless Steel Sea-Dog® Line drain plug and your existing drain hole to make this super bright light the world’s easiest to install - and safest with reverse polarity protection. The efficient underwater lighting solution for boats up to 25’.

With a life span of more than 40,000 hours and Active Thermal Control, a built-in temperature monitoring system, the Amphibian Drain Plug can be used while under way, at anchor attracting fish, idle at the pier, or as a flood light above the water.

Installation is simple utilizing the existing drainplug hole; the T3s Drain Plug can retro-fit as a complete system in one. The T3 Drain Plug also has a unique 2-step design which allows drainage without removing the light or putting tension on the power cable.

Features:

2010TH HD Thru-Hull
001-500580 White w/Linear Optics

High Definition Underwater Lighting Excellence

The Original Thru-Hull with the world’s smallest hole cut-out for a thru hull light at only 1" now just got 130% brighter than its predecessor using the latest High Definition LEDs. The 2010TH HD with a 1 inch (30mm) profile head and the brightness equivalent to 150w HID/Metal Halide products making it ideal for transom mount applications.
Ideally suited for boats up to and over 65’ (20m) using 2-6 lights with spacing of 3-5’ (1-1.5m). Using Deutsch plug-and-play quick connectors, the lights are a quick fit.
Suitable for Fiberglass, GRP and wooden hulls, and also available for use on aluminium/steel hulls using a Delrin Isolation Sleeve option.

Features:

• 1’ Hole in Hull
  
• 2.3x Brighter than the Original 2010
  
• Equal to 150w HID/Metal Halide
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

2010TH HD Thru-Hull
001-500582 Midnight Blue w/Linear Optics

High Definition Underwater Lighting Excellence

The Original Thru-Hull with the world’s smallest hole cut-out for a thru hull light at only 1" now just got 130% brighter than its predecessor using the latest High Definition LEDs. The 2010TH HD with a 1 inch (30mm) profile head and the brightness equivalent to 150w HID/Metal Halide products making it ideal for transom mount applications.
Ideally suited for boats up to and over 65’ (20m) using 2-6 lights with spacing of 3-5’ (1-1.5m). Using Deutsch plug-and-play quick connectors, the lights are a quick fit.
Suitable for Fiberglass, GRP and wooden hulls, and also available for use on aluminium/steel hulls using a Delrin Isolation Sleeve option.

Features:

• 1’ Hole in Hull
  
• 2.3x Brighter than the Original 2010
  
• Equal to 150w HID/Metal Halide
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

2010TH HD Thru-Hull
001-500584 Sea Green w/Linear Optics

High Definition Underwater Lighting Excellence

The Original Thru-Hull with the world’s smallest hole cut-out for a thru hull light at only 1" now just got 130% brighter than its predecessor using the latest High Definition LEDs. The 2010TH HD with a 1 inch (30mm) profile head and the brightness equivalent to 150w HID/Metal Halide products making it ideal for transom mount applications.
Ideally suited for boats up to and over 65’ (20m) using 2-6 lights with spacing of 3-5’ (1-1.5m). Using Deutsch plug-and-play quick connectors, the lights are a quick fit.
Suitable for Fiberglass, GRP and wooden hulls, and also available for use on aluminium/steel hulls using a Delrin Isolation Sleeve option.

Features:

• 1’ Hole in Hull
  
• 2.3x Brighter than the Original 2010
  
• Equal to 150w HID/Metal Halide
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

3010TH HD Thru-Hull
001-500587 White w/Linear Optics

High Definition Underwater Lighting Excellence

The Original Thru-Hull with the world’s smallest hole cut-out for a thru hull light at only 1" now just got 100% brighter than its predecessor using the latest High Definition LEDs. The 3010TH HD with a 1 inch (30mm) profile head and the brightness equivalent to 250w HID/Metal Halide products makes it ideal for transom mount applications on larger boats.
Ideally suited for boats of 65’ (20m) or above using 4 or more lights with spacing of 3-6’ (1-1.8m). Using Deutsch plug-and-play quick connectors, the lights are a quick fit.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• 1" Hole in Hull
  
• 2x Brighter than the Original 3010
  
• Equal to 250w HID/Metal Halide
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

3010TH HD Thru-Hull
001-500589 Midnight Blue w/Linear Optics

High Definition Underwater Lighting Excellence

The Original Thru-Hull with the world’s smallest hole cut-out for a thru hull light at only 1" now just got 100% brighter than its predecessor using the latest High Definition LEDs. The 3010TH HD with a 1 inch (30mm) profile head and the brightness equivalent to 250w HID/Metal Halide products makes it ideal for transom mount applications on larger boats.
Ideally suited for boats of 65’ (20m) or above using 4 or more lights with spacing of 3-6’ (1-1.8m). Using Deutsch plug-and-play quick connectors, the lights are a quick fit.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• 1" Hole in Hull
  
• 2x Brighter than the Original 3010
  
• Equal to 250w HID/Metal Halide
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

3010TH HD Thru-Hull
001-500591 Sea Green w/Linear Optics

High Definition Underwater Lighting Excellence

The Original Thru-Hull with the world’s smallest hole cut-out for a thru hull light at only 1" now just got 100% brighter than its predecessor using the latest High Definition LEDs. The 3010TH HD with a 1 inch (30mm) profile head and the brightness equivalent to 250w HID/Metal Halide products makes it ideal for transom mount applications on larger boats.
Ideally suited for boats of 65’ (20m) or above using 4 or more lights with spacing of 3-6’ (1-1.8m). Using Deutsch plug-and-play quick connectors, the lights are a quick fit.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• 1" Hole in Hull
  
• 2x Brighter than the Original 3010
  
• Equal to 250w HID/Metal Halide
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

2010XFM HD Xchangeable Flush Mount
001-500626 Sea Green w/Linear Optics

High Definition Underwater Lighting Excellence

The New Xchangealbe Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options and can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output.
The 2010XFM HD with the brightness equivalent to 150w HID/Metal Halide products is 130% brighter than earlier model 2010’s using the latest High Definition LEDs.
Ideally suited for boats of 65’ (20m) or above using 2-6 lights per side with spacing of 3-5’ (1-1.5m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• Exchangeable from Inside the Hull
  
• 2.3x Brighter than the Original 2010
  
• Equal to 150w HID/Metal Halide
  
• 4" Hole
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2 Bezel/Hard Anodized Aluminium Body
  
• Plug & Play
  
• Factory Sealed Unit

2010XFM HD Xchangeable Flush Mount
001-500628 Multi-Colored w/Linear Optics

High Definition Underwater Lighting Excellence

The New Xchangealbe Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options and can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output.
The 2010XFM HD with the brightness equivalent to 150w HID/Metal Halide products is 130% brighter than earlier model 2010’s using the latest High Definition LEDs.
Ideally suited for boats of 65’ (20m) or above using 2-6 lights per side with spacing of 3-5’ (1-1.5m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• Exchangeable from Inside the Hull
  
• 2.3x Brighter than the Original 2010
  
• Equal to 150w HID/Metal Halide
  
• 4" Hole
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2 Bezel/Hard Anodized Aluminium Body
  
• Plug & Play
  
• Factory Sealed Unit

3010XFM HD Xchangeable Flush Mount
001-500629 White w/Linear Optics

High Definition Underwater Lighting Excellence

The New Xchangealbe Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options and can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output.
The 3010XFM HD with the brightness equivalent to 250w HID/Metal Halide products is 100% brighter than earlier model 3010’s using the latest High Definition LEDs.
Ideally suited for boats of 65’ (20m) or above using 4 or more lights per side with spacing of 4-8’ (1.2-2.4m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• Exchangeable from Inside the Hull
  
• 2x Brighter than the Original 3010
  
• Equal to 250w HID/Metal Halide
  
• 4-½" Hole
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2 Bezel/Hard Anodized Aluminium Body
  
• Plug & Play
  
• Factory Sealed Unit

3010XFM HD Xchangeable Flush Mount
001-500631 Midnight Blue w/Linear Optics

High Definition Underwater Lighting Excellence

The New Xchangealbe Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options and can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output.
The 3010XFM HD with the brightness equivalent to 250w HID/Metal Halide products is 100% brighter than earlier model 3010’s using the latest High Definition LEDs.
Ideally suited for boats of 65’ (20m) or above using 4 or more lights per side with spacing of 4-8’ (1.2-2.4m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• Exchangeable from Inside the Hull
  
• 2x Brighter than the Original 3010
  
• Equal to 250w HID/Metal Halide
  
• 4-½" Hole
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2 Bezel/Hard Anodized Aluminium Body
  
• Plug & Play
  
• Factory Sealed Unit

3010XFM HD Xchangeable Flush Mount
001-500633 Sea Green w/Linear Optics

High Definition Underwater Lighting Excellence

The New Xchangealbe Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options and can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output.
The 3010XFM HD with the brightness equivalent to 250w HID/Metal Halide products is 100% brighter than earlier model 3010’s using the latest High Definition LEDs.
Ideally suited for boats of 65’ (20m) or above using 4 or more lights per side with spacing of 4-8’ (1.2-2.4m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• Exchangeable from Inside the Hull
  
• 2x Brighter than the Original 3010
  
• Equal to 250w HID/Metal Halide
  
• 4-½" Hole
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2 Bezel/Hard Anodized Aluminium Body
  
• Plug & Play
  
• Factory Sealed Unit

3010XFM HD Xchangeable Flush Mount
001-500635 Multi-Colored w/Linear Optics

High Definition Underwater Lighting Excellence

The New Xchangealbe Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options and can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output.
The 3010XFM HD with the brightness equivalent to 250w HID/Metal Halide products is 100% brighter than earlier model 3010’s using the latest High Definition LEDs.
Ideally suited for boats of 65’ (20m) or above using 4 or more lights per side with spacing of 4-8’ (1.2-2.4m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• Exchangeable from Inside the Hull
  
• 2x Brighter than the Original 3010
  
• Equal to 250w HID/Metal Halide
  
• 4-½" Hole
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2 Bezel/Hard Anodized Aluminium Body
  
• Plug & Play
  
• Factory Sealed Unit

2010XFM HD Xchangeable Flush Mount
001-500622 White w/Linear Optics

High Definition Underwater Lighting Excellence

The New Xchangealbe Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options and can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output.
The 2010XFM HD with the brightness equivalent to 150w HID/Metal Halide products is 130% brighter than earlier model 2010’s using the latest High Definition LEDs.
Ideally suited for boats of 65’ (20m) or above using 2-6 lights per side with spacing of 3-5’ (1-1.5m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• Exchangeable from Inside the Hull
  
• 2.3x Brighter than the Original 2010
  
• Equal to 150w HID/Metal Halide
  
• 4" Hole
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2 Bezel/Hard Anodized Aluminium Body
  
• Plug & Play
  
• Factory Sealed Unit

2010XFM HD Xchangeable Flush Mount
001-500624 Midnight Blue w/Linear Optics

High Definition Underwater Lighting Excellence

The New Xchangealbe Flush Mount has an exceptionally low profile giving it virtually unlimited hull mounting options and can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output.
The 2010XFM HD with the brightness equivalent to 150w HID/Metal Halide products is 130% brighter than earlier model 2010’s using the latest High Definition LEDs.
Ideally suited for boats of 65’ (20m) or above using 2-6 lights per side with spacing of 3-5’ (1-1.5m). A very quick-to-fit light using Deutsch plug-and-play quick connect electrical installation system.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• Exchangeable from Inside the Hull
  
• 2.3x Brighter than the Original 2010
  
• Equal to 150w HID/Metal Halide
  
• 4" Hole
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2 Bezel/Hard Anodized Aluminium Body
  
• Plug & Play
  
• Factory Sealed Unit

2010FM HD Flush Mount
001-500601 White w/Linear Optics

High Definition Underwater Lighting Excellence

The Flush Mount HD has an exceptionally low profile giving it virtually unlimited hull mounting options. This light can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output.
The 2010FM HD with the brightness equivalent to 150w HID/Metal Halide products is 130% brighter than earlier model 2010’s using the latest High Definition LEDs.
Ideally suited for boats up to 65’ (20m) using 2-6 lights per side with spacing of 3-6’ (1-1.8m). A very quick-to-fit light using Deutsch plug and play quick connect electrical installation system.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features:

• 3-¼" Hole - Easy to Retrofit
  
• 2.3x Brighter than the Original 2010
  
• Equal to 150w HID/Metal Halide
  
• 24vDC
  
• 40,000+ Hour Life
  
• Aluminium Bronze AB2
  
• Plug & Play
  
• Factory Sealed Unit
  
• No Breakable Parts

2010FM HD Flush Mount
001-500603 Midnight Blue w/Linear Optics

High Definition Underwater Lighting Excellence

The Flush Mount HD has an exceptionally low profile giving it virtually unlimited hull mounting options. This light can be retrofitted into most existing underwater lighting hole cut-outs, offering immediate benefits of no startup power surge, low heat, minimal maintenance and improved light output.
The 2010FM HD with the brightness equivalent to 150w HID/Metal Halide products is 130% brighter than earlier model 2010’s using the latest High Definition LEDs.
Ideally suited for boats up to 65’ (20m) using 2-6 lights per side with spacing of 3-6’ (1-1.8m). A very quick-to-fit light using Deutsch plug and play quick connect electrical installation system.
Suitable for Fiberglass, GRP and wooden hulls, and now also available for use on aluminium/steel hulls using the Delrin Sleeve option.

Features: