Flex-Mount System - Rail Mount

Use with Scanstrut Helm Pod models on low rails, powerboat consoles, twin helm yachts, etc.

• Allows display to be rotated to be viewed from any angle - locks / unlocks into position
  
• Tilt display forward / back for improved instrument viewing
  
• Fits range of rail sizes

Flex-Mount System - Rail Mount

Use with Scanstrut Helm Pod models on low rails, powerboat consoles, twin helm yachts, etc.

• Allows display to be rotated to be viewed from any angle - locks / unlocks into position
  
• Tilt display forward / back for improved instrument viewing
  
• Fits range of rail sizes

Flex-Mount System - Rail Mount

Use with Scanstrut Helm Pod models on low rails, powerboat consoles, twin helm yachts, etc.

• Allows display to be rotated to be viewed from any angle ? locks / unlocks into position
  
• Tilt display forward / back for improved instrument viewing
  
• Fits range of rail sizes

Adjustable mount which can be installed on the cabin roof, flybridge and radar arches to provide a level mounting for your camera on any sloping surface.

By elevating your antenna clear of obstructions, PowerTower® maximizes the performance of your radar. Based on our unique ellipse shaped extrusion, our aluminium PowerTower® offers great strength and durability with minimum weight.

Features

• For Furuno, JRC, Sitex and Northstar Radomes
  
• 25° forward leaning streamlined profile
  
• Hollow stem allowing internal routing of all cables
  
• Watertight base seal supplied
  
• Pre-fitted watertight (IP65) cable gland
  
• Small mounting footprint of only 180mm²/7in²
  
• Pre-drilled base for quick installation
  
• Finished in corrosion resistant polyester powder coating
  
• 250mm (10") for low level clearance of smaller obstacles

By elevating your antenna clear of obstructions, PowerTower® maximizes the performance of your radar. Based on our unique ellipse shaped extrusion, our aluminium PowerTower® offers great strength and durability with minimum weight.

Features

• 25° forward leaning streamlined profile
  
• For Raymarine and Furuno Open Array Antennas
  
• Hollow stem allowing internal routing of all cables
  
• Watertight base seal supplied
  
• Pre-fitted watertight (IP65) cable gland
  
• Small mounting footprint of only 180mm²/7in²
  
• Pre-drilled base for quick installation
  
• Finished in corrosion resistant polyester powder coating
  
• 130mm (6") for low level clearance of smaller obstacles

By elevating your antenna clear of obstructions, PowerTower® maximizes the performance of your radar. Based on our unique ellipse shaped extrusion, our aluminium PowerTower® offers great strength and durability with minimum weight.

Features

• 25° forward leaning streamlined profile
  
• For Raymarine and Garmin Domes
  
• Hollow stem allowing internal routing of all cables
  
• Watertight base seal supplied
  
• Pre-fitted watertight (IP65) cable gland
  
• Small mounting footprint of only 180mm²/7in²
  
• Pre-drilled base for quick installation
  
• Finished in corrosion resistant polyester powder coating
  
• 130mm (5") for low level clearance of smaller obstacles

By elevating your antenna clear of obstructions, PowerTower® maximizes the performance of your radar. Based on our unique ellipse shaped extrusion, our aluminium PowerTower® offers great strength and durability with minimum weight.

Features

• 25° forward leaning streamlined profile
  
• For Raymarine and Garmin Domes
  
• Hollow stem allowing internal routing of all cables
  
• Watertight base seal supplied
  
• Pre-fitted watertight (IP65) cable gland
  
• Small mounting footprint of only 180mm²/7in²
  
• Pre-drilled base for quick installation
  
• Finished in corrosion resistant polyester powder coating
  
• 250mm (10") for greater clearance and increased radar horizon

By elevating your antenna clear of obstructions, PowerTower® maximizes the performance of your radar. Manufactured using the best composite materials, PowerTower is molded as a single 'monocoque' structure with no joints, offering unparalleled strength and durability.

There is a PowerTower® to fit pretty much every modern radar, including open array.

Features

• 30° aft leaning streamline profile
  
• For Raymarine and Garmin Domes
  
• Hollow stem allowing internal routing of all cables
  
• Watertight base seal supplied
  
• Pre-fitted watertight (IP65) cable gland
  
• Small mounting footprint of only 200mm² /8in²
  
• Pre-drilled base for quick installation
  
• Available in two height options:

By elevating your antenna clear of obstructions, PowerTower® maximizes the performance of your radar. Manufactured using the best composite materials, PowerTower® is molded as a single ’monocoque’ structure with no joints, offering unparalleled strength and durability.

There is a PowerTower® to fit pretty much every modern radar, including open array.

Features

By elevating your antenna clear of obstructions, PowerTower® maximizes the performance of your radar. Manufactured using the best composite materials, PowerTower® is molded as a single ’monocoque’ structure with no joints, offering unparalleled strength and durability.

There is a PowerTower® to fit pretty much every modern radar, including open array.

Features

By elevating your antenna clear of obstructions, PowerTower® maximizes the performance of your radar. Manufactured using the best composite materials, PowerTower is moulded as a single 'monocoque' structure with no joints, offering unparalleled strength and durability.

There is a PowerTower® to fit pretty much every modern radar, including open array.

Features

• 30° aft leaning streamline profile
  
• Hollow stem allowing internal routing of all cables
  
• Watertight base seal supplied
  
• Pre-fitted watertight (IP65) cable gland
  
• Small mounting footprint of only 200mm² /8in²
  
• Pre-drilled base for quick installation
  
• Available in two height options:

By elevating your antenna clear of obstructions, PowerTower® maximizes the performance of your radar. Manufactured using the best composite materials, PowerTower® is molded as a single ’monocoque’ structure with no joints, offering unparalleled strength and durability.

There is a PowerTower® to fit pretty much every modern radar, including open array.

Features

• For Garmin or Furuno Radomes
  
• 30° aft leaning streamline profile
  
• Hollow stem allowing internal routing of all cables
  
• Watertight base seal supplied
  
• Pre-fitted watertight (IP65) cable gland
  
• Small mounting footprint of only 200mm² /8in²
  
• Pre-drilled base for quick installation
  
• 150mm (6") for low level clearance of smaller obstacles

By elevating your antenna clear of obstructions, PowerTower® maximizes the performance of your radar. Manufactured using the best composite materials, PowerTower® is molded as a single ’monocoque’ structure with no joints, offering unparalleled strength and durability.

There is a PowerTower® to fit pretty much every modern radar, including open array.

Features

• For the KVH Tracphone 252
  
• Aft leaning streamline profile
  
• Hollow stem allowing internal routing of all cables
  
• Watertight base seal supplied
  
• Pre-fitted watertight (IP65) cable gland
  
• Small mounting footprint
  
• Pre-drilled base for quick installation

Mount light above the radar, clear of all obstructions for maximum performance and visibility.

Features

• Fits all PowerTower models and all SC100 Poles and SC2 poles
  
• Suitable for all 12", 18" and 24" radomes
  
• All mounting holes pre-drilled for easy retrofit installation
  
• All cables run internally
  
• Port mounted light bar fits all Perko series 200 and Aqua signal series 25 & 40 all round white lights
  

Mounts light, GPS, VHF and Navtex antennas above the radar, clear of all obstructions for maximum performance and visibility.

Features

• SC111 Starboard mounted GPS / VHF / Navtex bar
  
• Fits all PowerTower models and all SC100 Poles and SC2 poles
  
• Suitable for all 12", 18" and 24" radomes
  
• All mounting holes pre-drilled for easy retrofit installation
  
• All cables run internally
  
• GPS / VHF / Navtex bars are available in both port and starboard mounted options allowing up to two additional antennas to be mounted above the main radar
  
• Port mounted light bar fits all Perko series 200 and Aqua signal series 25 & 40 all round white lights
  
• GPS / VHF / Navtex bar fits standard 14TPI 1" GPS mounts

Mounts light, GPS, VHF and Navtex antennas above the radar, clear of all obstructions for maximum performance and visibility.

Features

• SC112 Port mounted GPS / VHF / Navtex bar
  
• Fits all PowerTower models and all SC100 Poles and SC2 poles
  
• Suitable for all 12", 18" and 24" radomes
  
• All mounting holes pre-drilled for easy retrofit installation
  
• All cables run internally
  
• GPS / VHF / Navtex bars are available in both port and starboard mounted options allowing up to two additional antennas to be mounted above the main radar
  
• Port mounted light bar fits all Perko series 200 and Aqua signal series 25 & 40 all round white lights
  
• GPS / VHF / Navtex bar fits standard 14TPI 1" GPS mounts
  

Self Levelling Radar Mount - Mast

Compatible Units

• Garmin GMR18/GMR18HD/GMR24HD
  
• Raymarine RD218/RD424
  
• Simrad DX45/DX60

• Hydraulic damping to eliminate minor oscillations
  
• Sealed system - entirely maintenance free
  
• Passive system - no power required
  
• Reduced weight aloft - complete system weighs only 3.4 kg
  
• Easy upgrade from fixed mast mount - same mounting footprint as SC20 & M92722
  
• Attached to mast by four swivel ffet - matches the profile of any mast
  
• 12 point fixing - highest quality monel rivets
  
• Compact mount - radar extends only minimum distance from front of mast

• Finest quality machined and anodised aluminium mast adapter
  
• Marine grade 316 stainless steel cradle and base plate

• 1 x Levelling mount
  
• 1 x Mast Adapter
  
• 1 x Complete fastening pack

Self Levelling Radar Mount - Mast

Compatible Units

• Furuno 1623/1715/1824/1724/1734/1832/1834/NavNet
  
• Lowrance LRA-1800
  
• Northstar M series/8000i (18" 2kW)
  
• Simrad NX40/45 (18" 2kW)

• Hydraulic damping to eliminate minor oscillations
  
• Sealed system - entirely maintenance free
  
• Passive system - no power required
  
• Reduced weight aloft - complete system weighs only 3.4 kg
  
• Easy upgrade from fixed mast mount - same mounting footprint as SC20 & M92722
  
• Attached to mast by four swivel ffet - matches the profile of any mast
  
• 12 point fixing - highest quality monel rivets
  
• Compact mount - radar extends only minimum distance from front of mast

• Finest quality machined and anodised aluminium mast adapter
  
• Marine grade 316 stainless steel cradle and base plate

• 1 x Levelling mount
  
• 1 x Mast Adapter
  
• 1 x Complete fastening pack

Mast Mounts

Still the first choice for boat owners the world over, Scanstrut Mast Mounts are the ultimate solution for mounting radars on yachts masts.

Raising the antenna clear of any obstructions or interference, the mast mount is a classic and reliable installation.

Features

• Easy and quick to install with all fastenings supplied
  
• Attached to mast by four swivel feet matching the profile of any mast
  
• 12 point fixing using highest quality Monel rivets for a secure installation
  
• Nylon washers for all fastenings to protect paint finish
  
• Waterproof cable grommet included to seal cable entry into mast

• Marine grade 6082 aluminum
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Mast Mount
  
• 4 x Swivel mounting feet
  
• 1 x Complete fastening pack

Mast Mounts

Still the first choice for boat owners the world over, Scanstrut Mast Mounts are the ultimate solution for mounting radars on yachts masts.

Raising the antenna clear of any obstructions or interference, the mast mount is a classic and reliable installation.

Features

• Easy and quick to install with all fastenings supplied
  
• Attached to mast by four swivel feet matching the profile of any mast
  
• 12 point fixing using highest quality Monel rivets for a secure installation
  
• Nylon washers for all fastenings to protect paint finish
  
• Waterproof cable grommet included to seal cable entry into mast

• Marine grade 6082 aluminium
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Mast Mount
  
• 4 x Swivel mounting feet
  
• 1 x Complete fastening pack

Mast Mounts

Compatible Units:

• Furuno Fleet 33/Felcom 30
  
• KVH TracPhone 252/Tracnet - Fleet Broadband 250(compact) - Fleet 33 (non G4 dome)
  
• Simrad MS33

• Easy and quick to install with all fastenings supplied
  
• Attached to mast by four swivel feet matching the profile of any mast
  
• 12 point fixing using highest quality Monel rivets for a secure installation
  
• Nylon washers for all fastenings to protect paint finish
  
• Waterproof cable grommet included to seal cable entry into mast

• Marine grade 6082 aluminum
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Mast Mount
  
• 4 x Swivel mounting feet
  
• 1 x Complete fastening pack

Mast Mounts For 18" Garmin, KVH M3 & Raymarine 37STV

Compatible Units:

• Garmin GMR18/GMR18HD
  
• Simrad DX45
  
• Intellian i3
  
• KVH TracVision M2/M3
  
• Raymarine 37STV
  
• Sea Tel Coastal 14

• Easy and quick to install with all fastenings supplied
  
• Attached to mast by four swivel feet matching the profile of any mast
  
• 12 point fixing using highest quality Monel rivets for a secure installation
  
• Nylon washers for all fastenings to protect paint finish
  
• Waterproof cable grommet included to seal cable entry into mast

• Marine grade 6082 aluminum
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Mast Mount
  
• 4 x Swivel mounting feet
  
• 1 x Complete fastening pack

Mast Mounts

Compatible Units:

• Furuno 1734/1832/1834/DRS4D/NavNet
  
• GMR24HD
  
• Interphase RE-8/RE-9
  
• Koden 4kW 20"/4kW (RB715A)
  
• Lowrance LRA2400 HD (w/ 19042 Adaptor)
  
• Northstar 24" (M Series/8000i) (w/ 19042 Adaptor)
  
• Simrad 24" (GB40/NX40/45) (w/ 19042 Adaptor)
  
• Simrad 24" (DX60) w/ 19042 Adaptor)
  
• Sitex MDS-9/Radarpc-4D

• Easy and quick to install with all fastenings supplied
  
• Attached to mast by four swivel feet matching the profile of any mast
  
• 12 point fixing using highest quality Monel rivets for a secure installation
  
• Nylon washers for all fastenings to protect paint finish
  
• Waterproof cable grommet included to seal cable entry into mast

• Marine grade 6082 aluminum
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Mast Mount
  
• 4 x Swivel mounting feet
  
• 1 x Complete fastening pack

Mast Mounts

Compatible Units:

• Raymarine: 2kW Radome

• Easy and quick to install with all fastenings supplied
  
• Attached to mast by four swivel feet matching the profile of any mast
  
• 12 point fixing using highest quality Monel rivets for a secure installation
  
• Nylon washers for all fastenings to protect paint finish
  
• Waterproof cable grommet included to seal cable entry into mast

• Marine grade 6082 aluminium
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Mast Mount
  
• 4 x Swivel mounting feet
  
• 1 x Complete fastening pack

Mast Mounts

Compatible Units:

• Raymarine: 4kW Radome

• Easy and quick to install with all fastenings supplied
  
• Attached to mast by four swivel feet matching the profile of any mast
  
• 12 point fixing using highest quality Monel rivets for a secure installation
  
• Nylon washers for all fastenings to protect paint finish
  
• Waterproof cable grommet included to seal cable entry into mast

• Marine grade 6082 aluminium
  
• Polyester powder coated for a durable and gloss white finish

Mast Mount Adapter Kit

Compatible With

• Compatible with Z-Spars, Selden, Isomat, Eurospars Masts

• Fits all Scanstrut Mast Mounts
  
• Compatible with Z-Spars, Selden, Isomat, Eurospars Masts

• Marine grade 6082 aluminium
  
• Polyester powder coated for a durable, gloss white finish

• 4 x Adapter rings
  
• 1 x Complete fastening pack

Satcom Antenna Mount

Compatible Units

• KVH: M3
  
• Raymarine: STV 37
  
• Sea Tel: Coastal 14
  
• Intellian®: i3

• Premium quality, high strength and corrosion free composite moulding
• Satcom mount fixings hidden internally
  
• Antenna fixings external for ease of antenna installation and maintenance
  
• Watertight installation - includes factory fitted watertight seal & gland systems

• Monocoque composite GRP moulding
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Satcom Mount
  
• 1 x Watertight seal

Satcom Antenna Mount

Compatible Units

• KVH: G4, M5
  
• Sea Tel: Coastal 18, 24, 30

• Premium quality, high strength and corrosion free composite moulding
• Satcom mount fixings hidden internally
  
• Antenna fixings external for ease of antenna installation and maintenance
  
• Watertight installation - includes factory fitted watertight seal & gland systems

• Monocoque composite GRP moulding
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Satcom Mount
  
• 1 x Watertight seal

Satcom Antenna Mount

Compatible Units

• Raymarine: STV 45
  
• Intellian: i4

• Premium quality, high strength and corrosion free composite moulding
  
• Satcom mount fixings hidden internally
  
• Antenna fixings external for ease of antenna installation and maintenance
  
• Watertight installation - includes factory fitted watertight seal & gland systems

• Monocoque composite GRP moulding
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Satcom Mount
  
• 1 x Watertight seal

Based on our unique ellipse extrusion, Scanstrut’s Aluminium PowerTower is designed to raise your antenna from the cabin roof, flybridge or radar arch, to ensure the radar has a clear view of the horizon and maximum performance can be achieved.

Available in a forward leaning profile for radome installations and an aft leaning profile for open-array installations.

Features

• Made specifically for Sitex, Simrad and Garmin
  
• Hollow stem to route cables neatly inside mount
  
• Pre-fitted waterproof IP65 gland to seal cable entry into stem
  
• Pre-drilled mounting holes for quick and easy installation
  
• Antenna fastens to PowerTower top plate using own mounting bolts
  
• Marine grade 6082 aluminum
  
• Polyester powder coated for a durable and gloss white finish

Self-Levelling Radar Mount - Backstay - Fwd (F) - Made Specifically for Raymarine & Garmin Domes

Our Self-Levelling Backstay Mount ensures your radar stays level with the horizon at all times for optimum antenna performance. As the boat heels or rolls, the radar is kept horizontal preventing target loss and giving the best possible radar picture.

Using our own fine-tuned hydraulic damping system, the radar mount reacts to major changes in heel angle of the boat whilst eliminating all small oscillations.

Features:

• Hydraulic damping to eliminate minor oscillations
  
• Sealed system - entirely maintenance free
  
• Passive system - no power required
  
• Lightweight head unit - reduced weight aloft
  
• Stainless radome cradle with fine tune adjustment for backstay angle - suitable for any yacht
  
• Nylon backstay bushing supplied - clamps around backstay allowing cable tension to be adjusted
  

• 2.6m pole - supplied in lengths of 1.3m
  
• Additional 0.6m and 1.3m lengths available
  

• Finest quality machined an anodised aluminum pole and head unit - lasts the lifetime of your yacht.
  
• Marine grade 316 stainless steel cradle and base plate
  

Self Levelling Radar Mount - Backstay - Fwd (F) Made specifically for Sitex & Simrad Domes

Our Self-Levelling Backstay Mount ensures your radar stays level with the horizon at all times for optimum antenna performance. As the boat heels or rolls, the radar is kept horizontal preventing target loss and giving the best possible radar picture.

Using our own fine-tuned hydraulic damping system, the radar mount reacts to major changes in heel angle of the boat whilst eliminating all small oscillations.

Features:

Self Levelling Radar Mount - Backstay - Aft (A) Made specifically for Raymarine/Garmin Domes

Our Self-Levelling Backstay Mount ensures your radar stays level with the horizon at all times for optimum antenna performance. As the boat heels or rolls, the radar is kept horizontal preventing target loss and giving the best possible radar picture.

Using our own fine-tuned hydraulic damping system, the radar mount reacts to major changes in heel angle of the boat whilst eliminating all small oscillations.

Features:

• Hydraulic damping to eliminate minor oscillations
  
• Sealed system - entirely maintenance free
  
• Passive system - no power required
  
• Lightweight head unit - reduced weight aloft
  
• Stainless radome cradle with fine tune adjustment for backstay angle - suitable for any yacht
  
• Nylon backstay bushing supplied - clamps around backstay allowing cable tension to be adjusted
  

• 2.6m pole - supplied in lengths of 1.3m
  
• Additional 0.6m and 1.3m lengths available
  

• Finest quality machined and anodised aluminium pole and head unit - lasts the lifetime of your yacht
  
• Marine grade 316 stainless steel cradle and base plate
  

Self Levelling Radar Mount - Backstay - Aft (A) - Made specifically for Sitex/Simrad Domes

Our Self-Levelling Backstay Mount ensures your radar stays level with the horizon at all times for optimum antenna performance. As the boat heels or rolls, the radar is kept horizontal preventing target loss and giving the best possible radar picture.

Using our own fine-tuned hydraulic damping system, the radar mount reacts to major changes in heel angle of the boat whilst eliminating all small oscillations.

Features:

• Hydraulic damping to eliminate minor oscillations
  
• Sealed system - entirely maintenance free
  
• Passive system - no power required
  
• Lightweight head unit - reduced weight aloft
  
• Stainless radome cradle with fine tune adjustment for backstay angle - suitable for any yacht
  
• Nylon backstay bushing supplied - clamps around backstay allowing cable tension to be adjusted
  

• 2.6m pole - supplied in lengths of 1.3m
  
• Additional 0.6m and 1.3m lengths available
  

• Finest quality machined and anodised aluminium pole and head unit - lasts the lifetime of your yacht
  
• Marine grade 316 stainless steel cradle and base plate
  

Self Levelling Radar Mount - Pole

Our Self-Levelling Pole Mount ensures your radar stays level with the horizon at all times for optimum antenna performance. As the boat heels or rolls, the radar is kept horizontal preventing target loss and giving the best possible radar picture.

Using our own fine-tuned hydraulic damping system, the radar mount reacts to major changes in heel angle of the boat whilst eliminating all small oscillations.

Features

• Sealed system - entirely maintenance free
  
• Universal adjustable base able to rotate through 360° and angle from horizontal all the way to vertical
  
• Supplied with two support modules - a deck strut and rail stand off for maximum fore / aft and sideways support
  
• Fits to angled decks, narrow swimming steps and steeply sloping transoms
  
• Unique pole extrusion with two cable channels with cover strips to hold cables in place
  
• Easily removed for racing or winter storage, leaving just low profile deck on deck
  
• Existing SC100 Pole Mount installations can be upgraded to self levelling with our upgrade kit

• 2.5m / 8.3’ pole
  
• 3" diameter pole
  
• Base diameter of just 80mm / 3.1"

• Finest quality machined and anodised aluminium head unit ? lasts the lifetime of your yacht
  
• Marine grade 316 stainless steel cradle and base plate
  
• Marine grade 6082 aluminium pole - polyester powder coated for a durable and gloss white finish

• 1 x Pole (complete with 2 x cable cover strips)
  
• 1 x Adjustable base
  
• 1 x Levelling head unit and cradle with plate
  
• 1 x 1200mm / 3.9’ deck strut
  
• 1 x Rail stand off for 25mm / 1" rail

Self Levelling Radar Mount - Pole

Our Self-Levelling Pole Mount ensures your radar stays level with the horizon at all times for optimum antenna performance. As the boat heels or rolls, the radar is kept horizontal preventing target loss and giving the best possible radar picture.

Using our own fine-tuned hydraulic damping system, the radar mount reacts to major changes in heel angle of the boat whilst eliminating all small oscillations.

Features

• Sealed system - entirely maintenance free
  
• Universal adjustable base able to rotate through 360° and angle from horizontal all the way to vertical
  
• Supplied with two support modules - a deck strut and rail stand off for maximum fore / aft and sideways support
  
• Fits to angled decks, narrow swimming steps and steeply sloping transoms
  
• Unique pole extrusion with two cable channels with cover strips to hold cables in place
  
• Easily removed for racing or winter storage, leaving just low profile deck on deck
  
• Existing SC100 Pole Mount installations can be upgraded to self levelling with our upgrade kit

• 2.5m / 8.3’ pole
  
• 3" diameter pole
  
• Base diameter of just 80mm / 3.1"

• Finest quality machined and anodised aluminium head unit ? lasts the lifetime of your yacht
  
• Marine grade 316 stainless steel cradle and base plate
  
• Marine grade 6082 aluminium pole - polyester powder coated for a durable and gloss white finish

• 1 x Pole (complete with 2 x cable cover strips)
  
• 1 x Adjustable base
  
• 1 x Levelling head unit and cradle with plate
  
• 1 x 1200mm / 3.9’ deck strut
  
• 1 x Rail stand off for 25mm / 1" rail

Dual Power Tower

Scanstrut’s Dual PowerTower® mounts allow the installation of radar and satcom antennas together on a single space-saving mount. Installing the satcom antenna above the radar eliminates antenna interference and ensures maximum performance from both applications.

Features

• Minimal mounting area required, can be installed even where deck space is limited
  
• Hollow stem to route cables neatly inside mount
  
• Pre-fitted waterproof IP65 gland to seal cable entry into stem
  
• Pre-drilled mounting holes for quick and easy installation

• 11.5" / 290mm square footprint

• Marine grade 6082 aluminium
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Dual PowerTower
  
• 1 x Watertight base seal
  
• 1 x Waterproof IP65 gland (pre-fitted)

Dual Power Tower

Scanstrut’s Dual PowerTower® mounts allow the installation of radar and satcom antennas together on a single space-saving mount. Installing the satcom antenna above the radar eliminates antenna interference and ensures maximum performance from both applications.

Features

• Minimal mounting area required, can be installed even where deck space is limited
  
• Hollow stem to route cables neatly inside mount
  
• Pre-fitted waterproof IP65 gland to seal cable entry into stem
  
• Pre-drilled mounting holes for quick and easy installation

• 11.5" / 290mm square footprint

• Marine grade 6082 aluminium
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Dual PowerTower
  
• 1 x Watertight base seal
  
• 1 x Waterproof IP65 gland (pre-fitted)

Dual Power Tower

Scanstrut’s Dual PowerTower® mounts allow the installation of radar and satcom antennas together on a single space-saving mount. Installing the satcom antenna above the radar eliminates antenna interference and ensures maximum performance from both applications.

Features

• Minimal mounting area required, can be installed even where deck space is limited
  
• Hollow stem to route cables neatly inside mount
  
• Pre-fitted waterproof IP65 gland to seal cable entry into stem
  
• Pre-drilled mounting holes for quick and easy installation

• 11.5" / 290mm square footprint

• Marine grade 6082 aluminium
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Dual PowerTower
  
• 1 x Watertight base seal
  
• 1 x Waterproof IP65 gland (pre-fitted)

Dual Power Tower

Scanstrut’s Dual PowerTower® mounts allow the installation of radar and satcom antennas together on a single space-saving mount. Installing the satcom antenna above the radar eliminates antenna interference and ensures maximum performance from both applications.

Features

• Minimal mounting area required, can be installed even where deck space is limited
  
• Hollow stem to route cables neatly inside mount
  
• Pre-fitted waterproof IP65 gland to seal cable entry into stem
  
• Pre-drilled mounting holes for quick and easy installation

• 11.5" / 290mm square footprint

• Marine grade 6082 aluminium
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Dual PowerTower
  
• 1 x Watertight base seal
  
• 1 x Waterproof IP65 gland (pre-fitted)

Dual Power Tower

Scanstrut’s Dual PowerTower® mounts allow the installation of radar and satcom antennas together on a single space-saving mount. Installing the satcom antenna above the radar eliminates antenna interference and ensures maximum performance from both applications.

Features

• Minimal mounting area required, can be installed even where deck space is limited
  
• Hollow stem to route cables neatly inside mount
  
• Pre-fitted waterproof IP65 gland to seal cable entry into stem
  
• Pre-drilled mounting holes for quick and easy installation

• 11.5" / 290mm square footprint

• Marine grade 6082 aluminium
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Dual PowerTower
  
• 1 x Watertight base seal
  
• 1 x Waterproof IP65 gland (pre-fitted)

Dual Power Tower

Scanstrut’s Dual PowerTower® mounts allow the installation of radar and satcom antennas together on a single space-saving mount. Installing the satcom antenna above the radar eliminates antenna interference and ensures maximum performance from both applications.

Features

• Minimal mounting area required, can be installed even where deck space is limited
  
• Hollow stem to route cables neatly inside mount
  
• Pre-fitted waterproof IP65 gland to seal cable entry into stem
  
• Pre-drilled mounting holes for quick and easy installation

• 11.5" / 290mm square footprint

• Marine grade 6082 aluminium
  
• Polyester powder coated for a durable and gloss white finish

• 1 x Dual PowerTower
  
• 1 x Watertight base seal
  
• 1 x Waterproof IP65 gland (pre-fitted)

Scanstrut’s SC101 Pole Mount allows installation of your radar or 30cm or 40cm satcom antenna onto the deck or transom of your boat.

Features:

• Adjustable base, able to rotate through 360x and angle from horizontal all the way to vertical
  
• Unique pole extrusion accommodates two cable channels with a cover strip to hold cables in place
  
• Supplied with two support modules providing maximum fore / aft and sideways bracing
  
• Easily removed for racing or winter storage, leaving just low profile base on deck
  

• 1.9m / 6.4’ recommended for deck mounting
  
• 3" diameter pole
  
• Base diameter of just 80mm / 3.1"
  

• Marine grade 6082 aluminium pole
  
• Polyester powder coated for a durable and gloss white finish
  

Scanstrut’s SC103 Pole Mount allows installation of your radar or 30cm or 40cm satcom antenna onto the deck or transom of your boat.

Features:

• Adjustable base, able to rotate through 360x and angle from horizontal all the way to vertical
  
• Unique pole extrusion accommodates two cable channels with a cover strip to hold cables in place
  
• Supplied with two support modules providing maximum fore / aft and sideways bracing
  
• Easily removed for racing or winter storage, leaving just low profile base on deck
  

• 1.9m / 6.4’ recommended for deck mounting
  
• 3" diameter pole
  
• Base diameter of just 80mm / 3.1"
  

• Marine grade 6082 aluminium pole
  
• Polyester powder coated for a durable and gloss white finish
  

Totally universal, the SC105 Pole Mount installs your radar or satcom antenna onto the deck or transom of your boat.

Supplied as a complete kit, you will have everything you need for a quick and easy installation.

Totally universal, the SC105 Pole Mount installs your radar or satcom antenna onto the deck or transom of your boat.

Supplied as a complete kit, you will have everything you need for a quick and easy installation.

Totally universal, the SC105 Pole Mount installs your radar or satcom antenna onto the deck or transom of your boat.

Supplied as a complete kit, you will have everything you need for a quick and easy installation.

Space on board is always limited for installing satcom/tv antennas. Scanstrut Mounts eliminate this problem by reducing the mounting footprint size by up to 60%, providing greater choice of antenna position and a quick and easy installation.

These high quality installations guarantee maximum performance from your satcom antenna.

Features:

• Premium quality, high strength and corrosion free composite molding
  
• Satcom mount fixings hidden internally
  
• Antenna fixings external for ease of antenna installation and maintenance
  
• Watertight installation - includes factory fitted watertight seal & gland systems

Tapered Radar Mast
Single combintation mount for radar, lights, GPS/VHF antennas, cameras or search lights, with each item perfectly positioned for maximum performance.

• Undrilled top plate to fit any light
  
• Install up to 4 GPS/VHF antenna
  
• Hollow wings and stem allow hidden cabling
  
• Compatible with all current 18" and 24" radomes
  
• Small base footprint (same as Dual PowerTower)
  
• Removable ’wings’ for safe low cost shipping

Reduce the footprint size of your satcom antenna by up to 60% with the Scanstrut Satcom Antenna Mount. This gives you greater choice when choosing where to install your satcom antenna and also aids installation on narrow radar arches.

Features:

Standard Junction Box
The "fit and forget" Junction Box is the perfect sailing accessory for anyone planning boat maintenance.

Providing secure, watertight connections for marine electrical cables onboard any boat, they are manufactured from a glass reinforced plastic and provide capacity for up to 8 cables to enter the box.

Features:

Deluxe Junction Box

The "fit and forget" Junction Box is the perfect sailing accessory for anyone planning boat maintenance.

Providing secure, watertight connections for marine electrical cables onboard any boat, they are manufactured from a glass reinforced plastic and provide capacity for up to 8 cables to enter the box.

Features:

Rok-Lok Mount
Part #: AM-501-BKS

Designed with the sea in mind.

Scanstrut’s Rok-Lok Mount designed specifically for Humminbird’s 300 and 700 Series, Lowrance’s Elite-5 and Mark 5 Series.

A multi-position mount for small electronic devices onboard. Install fishfinders and chartplotter at the helm, RIB console, fishing boat dashboard, nav station and more.

Features:

• One-handed quick release lever, unlock, reposition and lock again
  
• Marine grade machined aluminum, anodized for a durable, impact resistant finish
  
• Ball and socket system gives smooth, secure adjustment
  
• Locking lever design provides a rock solid platform and a high clamping force
  
• To install on rails: Simply unscrew base and fit to Scanstrut Rail Mount accessory
  
• 360 degree rotation
  
• 180 degree of swivel/tilt

Rok-Lok Mount
Part #: AM-502-BKS

Designed with the sea in mind.

Scanstrut’s Rok-Lok Mount designed specifically for Garmin’s GPSMAP 400 & 500 Series, Garmin’s eco 100-550 Series and Garmin’s Fishfinder 90, 140 and 400.

A multi-position mount for small electronic devices onboard. Install fishfinders and chartplotter at the helm, RIB console, fishing boat dashboard, nav station and more.

Features:

• One-handed quick release lever, unlock, reposition and lock again
  
• Marine grade machined aluminum, anodized for a durable, impact resistant finish
  
• Ball and socket system gives smooth, secure adjustment
  
• Locking lever design provides a rock solid platform and a high clamping force
  
• To install on rails: Simply unscrew base and fit to Scanstrut Rail Mount accessory
  
• 360 degree rotation
  
• 180 degree of swivel/tilt

Rok-Lok MOunt
Part #: AM-503-BKS

Designed with the sea in mind.

Scanstrut’s Rok-Lok Mount designed specifically for Lowrance’s HDS-5 Series and Garmin’s Fishfinder 100, 160 and 300.

A multi-position mount for small electronic devices onboard. Install fishfinders and chartplotter at the helm, RIB console, fishing boat dashboard, nav station and more.

Features:

• One-handed quick release lever, unlock, reposition and lock again
  
• Marine grade machined aluminum, anodized for a durable, impact resistant finish
  
• Ball and socket system gives smooth, secure adjustment
  
• Locking lever design provides a rock solid platform and a high clamping force
  
• To install on rails: Simply unscrew base and fit to Scanstrut Rail Mount accessory
  
• 360 degree rotation
  
• 180 degree of swivel/tilt

Rok-Lok Mount
Part #: AM-504-BKS

Designed with the sea in mind.

Scanstrut’s Rok-Lok Mount designed specifically for Raymarine’s A50, A50D and A57D.

A multi-position mount for small electronic devices onboard. Install fishfinders and chartplotter at the helm, RIB console, fishing boat dashboard, nav station and more.

Features:

• One-handed quick release lever, unlock, reposition and lock again
  
• Marine grade machined aluminum, anodized for a durable, impact resistant finish
  
• Ball and socket system gives smooth, secure adjustment
  
• Locking lever design provides a rock solid platform and a high clamping force
  
• To install on rails: Simply unscrew base and fit to Scanstrut Rail Mount accessory
  
• 360 degree rotation
  
• 180 degree of swivel/tilt

Mast Mount
Part #: SC20-S

Strongest. Lightest. Easiest to fit.

Scanstrut’s Mast Mount specifically for 18" Garmin, KVH M3 and Raymarine’s STV37.

Still the first choice for boat owners the world over, Scanstrut Mast Mounts are the ultimate solution for mounting radars on yachts masts.

Raising the antenna clear of any obstructions or interference, the mast mount is a classic and reliable installation.

Features:

• Universal Mounting: Stiffer, stronger foot, 4 independent feet fit any mast profile
  
• Stongest Fixing: 12 point fixing using only the highest grade Monel rivets
  
• Compact Mounting: Antenna fits snugly, minimum projection from front of mast
  
• Saftey Wire: Independently attaches scanner to most in case an accident damages the installation

Through-Bulkhead Seal f/4 x 15mm Cables
Part #: TBH-4

Less Time. Less Cost. Better Waterproofing

Eliminate time consuming, sub-standard routing of cables though watertight bulkheads. Waterproof passage for multiple, mixed size electrical cables.

Features:

• IP67 Waterproof
  
• Up to 4 x 15mm (0.6") cables

Through-Bulkhead Seal f/10 x 7mm Cables
Part #: TBH-10

Less Time. Less Cost. Better Waterproofing

Eliminate time consuming, sub-standard routing of cables though watertight bulkheads. Waterproof passage for multiple, mixed size electrical cables.

Features:

• IP67 Waterproof
  
• Up to 10 x 7mm (0.27") cables

10-Pack Mini Deck Seal Connector
Part #: DS16-P-BULK

Features:

• Simply the best proven Deck Seals for antenna and navlight cables
  
• 100% waterproof
  
• Pass cables into the boat, anywhere on deck
  
• No need to remove cable plug