Weld Mount AT-1050 Retail Wire Tie Kit

The AT-1050 kit contains one manual mix tube of AT-804030 adhesive and 25 pc of AT-5 white wire tie mount. Just enough parts for a small wiring job and ideal introduction to Weld Mount

• 30 ML Tube AT-804030 Adhesive
• 25 Pieces AT-5 White Tie Mount
• 2 Mixing Sticks
• Complete Step By Step Instructions

Weld Mount AT-1001003 - Executive Adhesive Fastener Kit Weld Mount

The AT-1001003 Executive Adhesive and Fastener Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder.

The Kit Contains 1 Tube Of Our AT-8040 No Slide Multi-Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastic Or Rubber.

AT-8040 Will Hold Even Our Heaviest Parts on a Vertical or Overhead Surface Without Fixturing.

The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225 Degrees. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 9 Months.

• 1 pc. AT-8040 No Slide Multi Bonder Acrylic Adhesive
• 1 pc. AT-300 Dispensing Gun
• 10 pc. AT-850 3.5 in Mixing Tips For AT-8040 Adhesive
• 100 pc. AT-5 Large White Cable Tie Mount
• 100 pc. AT-5 Large White Cable Tie Mount
• 4 pc. AT-113 Large Footman’s Strap
• 4 pc. PS62-832-16SS 1.00 in Long Panel Stud
• 10 pc. ST125-1420-16SS 1.00 in Long Stud With 1?4 x 20 Threads 1.25 in Base
• 4 pc. ST125-1420-24SS 1.50 in Long Stud With 1?4 x 20 Threads 1.25 in Base
• 4 pc. ST125-1024-12SS 0.75 in Long Stud With #10 x 24 Threads 1.25 in Base
• 4 pc. ST125-1024-24SS 1.50 in Long Stud With #10 x 24 Threads 1.25 in Base
• 1pc Plano Storage Box 14 in x 9 in x 2.75 in
• Step By Step Instructions

Weld Mount Stainless Studs (#10-24 thread) 1.5tall 10 Pack

These #10-24 studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from either surface of the base plate.

• 10 Stainless Studs (#10-24 thread) 1.5"tall
"

Weld Mount AT-2010 Acrylic Adhesive

AT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. Heavier parts may need our AT-690 fixture dots to hold parts in place while the adhesive kicks.

AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength in 15 -20 minutes. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond.

AT-2010 has a 6 month shelf life when stored at 72 degrees. We recommend that where ever possible this adhesive be refrigerated.

Packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts

• AT-2010 Acrylic Adhesive

Weld Mount AT-6031 Metal & Carbon Adhesive 38ml

AT-6031 is a 10-to-1 metal bonding adhesive. It has high viscosity (cures in 10-12 minutes), has a 6-minute working time, and develops working strength in 40 minutes. AT-6031 develops more than 2,500 lbs. (psi) of tensile strength on most metal surfaces, making it an ideal alternative to welding in many applications.

AT-6031 has a 6-month shelf life and should always be stored refrigerated

Weld Mount

AT-7001 Industrial Fastener Kit

AT-7001 Industrial Fastener Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For Industrial Maintenance Shops. Supplied In A Heavy "Durham" Metal Box Which Is A Standard Rack Mounted System.

The Kit Contains 1 Tube Of Our AT-8040 No Slide Multi Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastics And Rubber.

AT-8040 Will Hold Even Our Heaviest Parts On An Overhead Or Vertical Surface Without Fixturing. The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225 Degrees. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 9 Months.

• 1 pc. AT-8040 No Slide Multi-Bonder Adhesive With 12 Minute Kick 10 pc. AT-850 3.5 in Mixing Tips For AT-8040 Adhesive
• 1 pc. AT-300 Adhesive Dispensing Gun
• 30 pc. AT-3B Small Black Cable Tie Mount
• 100 pc. AT-5B Large Black Cable Tie Mount and 25 pc. AT-5 Large White Cable Tie Moun
• 25 pc. AT-7 Aluminum Base Swivel Wire Tie Mount and 25 pc. AT-9 Aluminum Wire Tie Mount
• 2 pc. AT-113 Large Footman’s Strap White and 2 pc. AT-113B Large Footman’s Strap Black
• 6 pc. ST125-1420-12SS 0.75 in Long Stud With 1?4 x 20 Threads 1.25 in Base
• 6 pc. ST125-1420-12SS 0.75 in Long Stud With 1?4 x 20 Threads 1.25 in Base
• 6 pc. ST125-1024-12SS 0.75 in Long Stud With #10 x 24 Threads 1.25 in Base
• 6 pc. ST125-1024-20SS 1.25 in Long Stud With #10 x 24 Threads 1.25 in Base
• 2 pc. SHC-1000 Single Hose Clamp 1.00 in
• 2 pc. DHC-1000 Double Hose Clamp 1.00 in
• 1 pc. Storage Box Durham Manufacturing 18.5 feet x 12.5 in x 3.25 in
• Step By Step Instructions

Weld Mount AT-65100

The AT-65100 Adhesively Bonded Fastener Kit Has a Variety Of Weld Mount Parts Designed To Give The User The Chance To Try Our Weld Mount System At Low Cost.

The Kit Comes With A Dispensing Gun And Mixing Tips For Installation Of Our Adhesively Bonded Fasteners

The Kit Contains Our AT-8040 No Slide Multi-Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastic Or Rubber And Will Hold Up Even Our Heaviest Parts On A Vertical Or Overhead Surface.

The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225 Degrees. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 9

• 1 pc. AT-8040 No Slide Multi-Bonder Adhesive
• 1 pc. AT-300 Dispensing Gun
• 5 pc. AT-850 Mixing Tips
• 50pc. AT-5 White Tie Mount
• 2 pc. AT-113B Large Footman’s Strap Mount
• 4 Pc. ST125-1420-16SS Studs 0.75 in Tall
• 1 Plano Storage Box 11 in x 7.25 in x 2.75 in
• Step By Step Instructions

Weld Mount AT-300 Adhesive Dispensing Gun

The AT-300 Adhesive dispensing gun has a 1:1 plunger for use with AT-2010 and AT-4020 50ml cartridges. When using AT-6030 adhesive it requires AT-12 (10 to 1 plunger). Replacement plungers are also available.

• AT-300 Adhesive Dispensing Gun

Weld Mount AT-3 White Nylon Wire Tie Mount 500 Pack

The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20. Average pull strength is about 50 lbs. The square base measures .44 in wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs. (Also available in black)

• 500 AT-3 White Nylon Wire Tie Mounts
"

Weld Mount AT-3 Black Nylon Wire Tie Mount 500 Pack

The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20. Average pull strength is about 50 lbs. The square base measures .44 in wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs. (Also available in white)

• 500 AT-3 Black Nylon Wire Tie Mounts
"

Weld Mount AT-3 White Nylon Wire Tie Mount 50 Pack

The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20. Average pull strength is about 50 lbs. The square base measures .44 in wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs. (Also available in black)

• 50 AT-3 White Nylon Wire Tie Mounts
"

Weld Mount AT-3 White Nylon Wire Tie Mount 100 Pack

The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20. Average pull strength is about 50 lbs. The square base measures .44 in wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs. (Also available in black)

• 100 AT-3 White Nylon Wire Tie Mounts
"

Weld Mount AT-3 Black Nylon Wire Tie Mount 100 Pack

The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20. Average pull strength is about 50 lbs. The square base measures .44 in wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs. (Also available in white)

• 100 AT-3 Black Nylon Wire Tie Mounts
"

Weld Mount AT-3 Black Nylon Wire Tie Mount 50 Pack

The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20. Average pull strength is about 50 lbs. The square base measures .44 in wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs. (Also available in white)

• 50 AT-3 Black Nylon Wire Tie Mounts
"

Weld Mount AT-8040 No Slide Multi-Bonder

Weld Mount AT-8040 is a solvent free, VOC Compliant, two part methacrylate-based, structural adhesive formulated to bond metals for use in severe environments.

It will also bond engineered thermo- and thermosetting plastics, composites to metals or various substrate combinations. It has excellent adhesion to as received metal surfaces including aluminum, stainless steel, galvanized steel, and plated steels

AT-8040 forms a tough, high strength bonds usually with minimal surface preparation developing handling strength in 12 minutes and a functional cure within 45 minutes.

Ultimate strength exceeds 3500 psi of tensile shear strength on aluminum with remarkable impact and peel strengths. AT-8040 will hold all Weld Mount parts on a vertical or overhead surface without sagging when properly used.

• AT-8040 No Slide Multi-Bonder

Weld Mount AT-5 White Nylon Wire Tie Mount 500 Pack

The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs! (Also available in black)

• 500 AT-5 White Nylon Wire Tie Mounts

Well Mount AT-5 Black Nylon Wire Tie Mount 50 Pack

The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs! (Also available in white)

• 100 AT-5 Black Nylon Wire Tie Mounts

Weld Mount AT-5 Black Nylon Wire Tie Mount 500 Pack

The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs! (Also available in white)

• 500 AT-5 Black Nylon Wire Tie Mounts

Weld Mount AT-5 White Nylon Wire Tie Mount 100 Pack

The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs! (Also available in black)

• 100 AT-5 White Nylon Wire Tie Mounts

Well Mount AT-5 Black Nylon Wire Tie Mount 100 Pack

The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs! (Also available in white)

• 100 AT-5 Black Nylon Wire Tie Mounts

Weld Mount AT-5 White Nylon Wire Tie Mount 50 Pack

The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It’s designed for a #5 wire tie and has an average pull strength of 150 lbs. It’s approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs! (Also available in black)

• 50 AT-5 White Nylon Wire Tie Mounts

Weld Mount AT-850 Mixing Tip for AT-2010 and AT-8040 10 Pack

The At-850 tip is for use with AT-2010 and AT-8040. It’s unique design eliminates any possibility of the cartridge plugging up as the entry is separated.

• 10 AT-850 Mixing Tips for AT-2010 and AT-8040

Weld Mount AT-850 Mixing Tip for AT-2010 and AT-8040 100 Pack

The NEW at-850 tip is for use with AT-2010 and AT-8040. It’s unique design eliminates any possibility of the cartridge plugging up as the entry is separated.

• 100 AT-850 Mixing Tips

Weld Mount AT-850 Mixing Tip for AT-2010 and AT-8040 50 Pack

The at-850 tip is for use with AT-2010 and AT-8040. It’s unique design eliminates any possibility of the cartridge plugging up as the entry is separated.

• 50 AT-850 Mixing Tip for AT-2010 and AT-8040

Weld Mount Stainless Studs (#8-32 thread) .75 tall 15 Pack

These small panel studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels or for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62 in in diameter. Tensile strength is 300 lbs and shear strength is 375 lbs.

• 10 Stainless Studs (#8-32 thread) .75 in tall
"

Wel Mount Stainless Studs (#8-32 thread) 1 feet tall 15 Pack

These small panel studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels or for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62 in diameter. Tensile strength is 300 lbs and shear strength is 375 lbs.

• 15 Stainless Studs (#8-32 thread) 1 feet tall
"

Weld Mount Stainless Studs (#8-32 thread) 1.25 tall 15 Pack

These small panel studs have a wide range of uses. Originally they were used for mounting on The backside of dash panels or for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62 in in diameter.Tensile strength is 300 lbs and shear strength is 375 lbs.

• 15 Stainless Studs (#8-32 thread) 1.25 in tall
"

Weld Mount Stainless Studs (#8-32 thread) 1.5 tall 15 Pack

These small panel studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels or for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62 in in diameter. Tensile strength is 300 lbs and shear strength is 375 lbs.

• 15 Stainless Studs (#8-32 thread) 1.5 in tall
"